Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi, I have a project where I need to communicate using UART BLE between nRF51822 and a PC ThinkPad with Windows 8 and embedded BLE4.0 hardware.
I have programmed the nRF51822...
I'm running into a hardfault. I perform some initialization and enter a main loop. At the end of the main loop, I put the soft device into sleep mode and wait for an interrupt...
Hi,
Recently I updated my SoftDevice on beacon from 7.1.0 to 8.0.0. Unfortunately, I met the same problem with advertising timeout which I faced with in SD 7.1.0, but the...
Hi all,
I have some doubts over the memory management of nRF51822 and nRF51422-EK.
I have gone through the link in this forum where it is explained buy I'm still not sure...
I'm trying to build a project of "nRFUART_GoogleAPI_Android4.3+" from the following link.
[https://www.nordicsemi.com/eng/Products/nRFready-Demo-Apps/nRF-UART-App2]( www...
I have one doubt after reading the definition of PSTORAGE_MAX_APPLICATIONS and PSTORAGE_DATA_START_ADDR in pstorage_platform.h and the actual computation of used flash memory...
MCU : NordicSemi nRF51822-QFAA (Using custom board)
SDK Version : 7.2
Softdevice : S110 7.1
Using IAR for ARM 7.1
Hi, I was migrating my codes (SDK 6.1 to 7.2...
I am using the ble_app_template, together with one timer called every second. The timeout handler of the timer just prints a short string on the serial port using simple_uart...
Hell.
I will use flash from pstoreage.c . but seem to only use for bondmange. I find an define:
#define PSTORAGE_MAX_APPLICATIONS 2
This is just for "mp_flash_bond_info...
I'm struggling in implemented interrupt driven twi.
I found it always returned a overrun error after a successful RXD.
I saw an implementation by nordic employee in...
I try to move the code " github.com/.../nrf51-ble-app-lbs" to nRF52.
I meet this problem:
._build\nrf52832_xxaa_s132.axf: Error: L6218E: Undefined symbol app_gpiote_init...
I need to write an application that is mostly in sleep (not OFF) mode, waking once a second or so, and occasionally discovering that it has to do things. Without the softdevice...
I'm am trying to figure out what is causing the hardfault in my code. That question is here:
devzone.nordicsemi.com/.../
However, this question is more about understanding...
