Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
I can transmit data from my device (the server/peripheral) with the ble_app_hrs , but want to modify the peripheral behavior with some basic commands sent from the mobile...
I'm migrating from S310 v1.0 + SDK 5.2.0 to the latest S310 v2.0 + SDK 7.1.0 (to be able to update also BL and SD).
I have used OTA DFU based on example included in SDK...
Does the sdk7.1 + softdevice support flash_page_erase function?
Also, for the spi_master api, is the spi_master_event_handler required or optional?
currently, the...
Hi,
How to separate flash memory area that will not be overwritten when you upload new application code (e.g. a few bytes of static data). I'm using Keil.
Hi, I just flashed the BLE_proximity example in the ...\nrf51_sdk_v6_1_0_b2ec2e6\nrf51822\Board\nrf6310\s110\ble_app_proximity in the nRF51822 Development Kit, and the nFR...
I am working on a custom BLE service on the PCA10001. I can successfully detect and communicate with the PCA10001 using windows x64 MCP. I can also detect and communicate...
Dear Sirs
I am new with Nordic BLE Modules.
After successuful pairing with Windows 8.1 in a Tablet I need to get an active Service. For example I would like to obtain Battery...
We have an NRF51822 running S120 at 32MHz.
Our system has two removable batteries. If a battery is removed we need to switch to the other battery as fast as possible. We...
For TWI, SPI and UART is there a significant power savings from powering down the unit when not in use vs just disabling it?
Disabling the unit seems reasonable, but powering...
Hi!
I was trying to use nRFLoader to update firmware using example DFU Bootloader but app hangs on "Discovering" (after selecting device to update). What can be the reason...
Currently I can upload new application firmware smoothly (I use the dual bank setup). However, I have to use packets of size 20, so this takes a long time.
Is there actually...
hai ,
i am using the NRF51822 development kit. The NRF51 dongle i have used as a sniffer and a master control panel. Is it possible to load and run a s130 softdevice and...
Hi, I'm trying to estimate the nRF51422 current when running ANT. Does the softdevice use the RTC (LF oscillator) when in wait mode to save energy? Thanks
The Segger programing interface works. The virtual com port appears on my PC (COM5). The problem is that there is no board listed in the Motherboards section of the Device...
Hello,
currently I try to implement a GATT server on a nrf51422 with the s310 Softdevice. For testing I use the LightBlue IOS client on an ipad. I can see my GATT server...
