Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
hi guys,
i am trying to write my own application using ble_app_template for nRF51822, but i am not at all understanding the code, did anyone developed the code for it?...
hi,
i add bond function on my project ,
now the Master Control Panel can work correctly(show the Confirm Box )
but the iOS app(on LightBlue),not show any Confirm Box for...
Is possible to put S110 in observer role (as peripheral) , waiting for a specific advertising (or waiting for an active scanning) and then switch to advertiser role (always...
Hello all,
I'd like to use NRF UART App sample code (newest iOS7 version) to send data from iOS6 to nrf51822 for "real time" data transmission. But I found that when I...
Hi,
I am having some issues transferring data from an iPhone to the nRF51822.
Actually, I write block of 16 of my data from the iPhone on a specific characteristic on...
Hello,
I have been reading the documentation about how to program a BLuetooth Low Energy application. In that document, a lot of references to an specific mannual (nRF51822S110...
I am writing one bootloader to decide two apps resided in 0x14000 to 0x40000 with nrf51822 to run. Two apps works fine when starting running itself. But when bootloader switch...
Hi experts,
i found one issue that if i continue to make the 51822 advertise(if advertise timeout, start again), sometimes the 51822 will stop in somewhere. I'm sure that...
I have just acquired the NRF51822 Evaluation Kit and going through the getting started documentation. I can't seem to fix a compiler error which is highlighted in Kiel uVision...
Hi,
I am starting my first project with nRF51822 for my thesis.
I thought its a good idea to start with evolution kit so I bought nRF51822-EK
I assume I will get everything...
Hi, I'm trying to run your ble_app_hrs on your nrf51822 chip using internal rc clock: NRF_CLOCK_LFCLKSRC_RC_250_PPM_4000MS_CALIBRATION, so I pass this to the BLE_STACK_HANDLER_INIT...
Hello,
I have just bought an NRF51822-EK to familiarize myself with the micro-controller for a potential future job. Admittedly I feel like I am completely in over my head...
I've made a custom board with an nRF51422. The nRF51 part follows the reference schematics almost identically. After overcoming some reflow issues this board seems communicate...
