Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hello:
I have a problem here:
Connecting ... - Connecting via USB to probe/ programmer device 0 - Probe/ Programmer firmware: J-Link OB-nRF5340-NordicSemi compiled Apr...
Hello everyone,
I am planning to use the nRF9160 as the main microcontroller for my project. Alongside this, I need a Bluetooth module to transmit data to a mobile phone...
I'm using an nRF52840 as BLE peripheral with a custom service similar to NUS to send large data. The data is send in 4k chunks via BLE notifications to an Android phone. With...
In the nrf5340 Product Specification, the GPIO registers OUT, DIR, LATCH, DETECTMODE, DETECTMODE_SEC, and PIN_CNF[n] are all labeled as "Retained Registers". The definition...
I have had luck setting up signatures using MCUBOOT and sysbuild. However, I have not been able to encrypt the images. sysbuild.conf: SB_CONFIG_BOOTLOADER_MCUBOOT=y SB_CONFIG_BOOT_SIGNATURE_KEY_FILE...
I have a product that uses the nRF5 SDK that I do not plan to migrate to the nRF Connect SDK. My product uses ocrypto 3.0.8, which shipped with the latest version of the nRF5...
Hello,
I have an NRF9160DK board and a custom board running the SLM application that are exhibiting similar behaviour. Both boards work fine with the supplied iBasis SIM...
Here's a weird error, that started happening seemingly overnight: paths being parsed wrong on windows due to path separating backslashes being interpreted as escape sequences...
Hi,
I have done some searching and cannot find a direct answer to this. I have a gpio pin defined in a custom device in my board dts. I want to set this pin to high drive...
Is it posiible to use bt_disable on the nrf5340 board? for some reason it doesn't work, returns and error on this line:
if ( ! bt_dev . drv -> close ) {
return - ENOTSUP...
Hi all,
I need to modify the app.overlay dts overlay in mcuboot to be able to see the printout, among other small details. I was able to change them in the "C:/ncs/v2.5...
I'm switching from STM32 to nRF52840 and it's for a battery-operated device that only wakes up every few hours and only stays awake for about 10 seconds. With the STM32 (and...
One of our products uses the NRF51822 for Bluetooth communication.
This product is now undergoing CE certification. Is there a CE DoC (Declaration of Conformity) for the...
When creating a new board in the nRF Connect VSCode IDE, and just entering the basic items for name, if trying to use sysbuild there is a CMake error. I used name "foo" and...
I'm running Windows 11, have the kit connected with a microUSB cable and it shows up as a properly working nRF device on COM5 in device manager. I'm using v5.0.2 of nRF Connect...
