Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hello, I get the
"ERROR: The --family option given with the command (or the default from nrfjprog. ini)
ERROR: does not match the device connected."
message after...
Good morning,
this is Algocraft (www.algocraft.com), an high tech company whose core business is to develop, design and market a wide range of professional systems dedicated...
Hi,
We designed the circuit followed the reference circuit(QFN48), but we always failed in the 8kv ESD test.The CPU always reset while ESD testing.
The 8kv ESD power...
Hi,
I am developing on the nRF5340 and using an external modem and an external GNSS module. I am using SDK version 3.4.0.
To operate the modem, I use `modem_cellular...
Hello, We have some problem with connection to WIFI AP.
On NCS v3.4.0, once our device has associated with a WPA3-Personal AP, it can no longer
associate with a WPA2...
I am designing a board around the nRF52832 (QFN48). According to Table 5 in the product spec, GPIOs P0.22–P0.31 are marked "Low drive, low frequency I/O only" (see §4.3.1...
Hello,
Is modem fw `mfw_nrf9151-ntn_1.0.1` production-ready? Is it safe to have our manufacturer flash that instead of the `mfw_nrf91x1_2.0.4`. We are using the ncs-serial...
I'm trying to understand the npm1300-CAAA V1.1 example for configuration 1. The layout looks like this:
You can easily see that several pins are connected on the right...
According to the nRF52840 Product Specification, I observe only the typical value is specified below ：
ION_RAMON_RTC (System ON, full 256 kB RAM retention, wake on RTC...
Hi nordic
I am using the nRF54L10 and Nordic Zigbee Add-on version 1.3.0
I have probably been raising questions about polling for quite some time,
but I have not...
SUMMARY
A custom board (nRF52832, BLE Central + Peripheral roles simultaneously) reliably hits a hardware watchdog reset (RESETREAS shows WATCHDOG only, never CPU_LOCKUP...
Hello,
I have added DFU capabilities to my NRF54L15 project using:
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
and
SB_CONFIG_PARTITION_MANAGER =y
SB_CONFIG_BOOTLOADER_MCUBOOT...
Hello DevZone Community,
I wanted to share a unique hardware-in-the-loop implementation using the Power Profiler Kit II (PPK2). While the industry is heavily focused on...
I am designing an FPGA to have a SPI slave port connected to the nRF5340 SPIM4 master running at 32 MHz. But the setup and hold times for this configuration are missing from...
I have an application which is not able to talk with my gas gauge device when the TI EV2400 can. Looking at the waveforms all look the same except for the Zephyr code has...
our current network provider says that they have a restriction on their sim profile so that the mtu should be less than 1430. however things like pdn_dynamic_params_get()...
Have tried several times to install the SDK into VS code without success. This is one of the errors I am getting:
Failed to register SDK installation: west failed with...
