hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
I am migrating a project to Sysbuild where we previously were doing some post-build steps that require access to PM variables like PM_MCUBOOT_PRIMARY_SIZE.
Previously, we...
Hello, I've been trying to get MCUboot running on my custom board with the nRF9160 for two days now, and I'm honestly at my wit's end. The main application is written and...
Hello,
we are testing BLE MESH vs THREAD to build a home automation network.
We understood that WiFi interference is a real concern in this application. In fact, we...
Hi,Team,
I'm currently using the nrf54l15-dk. I want to set the rtc of the nrf54l15-dk to obtain the timestamp. How should I configure the timestamp ? Which examples should...
First, I can use I2C with SCL on pin P1.11 and SDA on P1.12 with NRF54L15DK.
But then, when I try to change SCL to P0.03 and SDA to P0.02. I2C does not work anymore.
The...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
Hi am trying to use Nrf54l15 as a controller with an external host for the Channel sounding feature. I can receive CS subevents from the NRF controller, but the same thing...
I am using a QFN73 pin package of nRF52840. The data sheet says it has built in balun. So if I follow the reference circuit, where do I see 50 ohm looking int to the chip...
having just seen the announcment about the bare-metal SDK, i gave it a try using my "hello world" of BLE -- a minimal beacon app which i actually use to benchmark BLE platforms...
Hi
I am capturing a digital signal with the nRF PowerProfiler Kit II from my board that can either be 12Hz or 2kHz depending on the state of my application.
In the below...
I am using an nrf52833 with MCU boot. In an abnormal situation, the Vcc hoovers around the BOD threshold of 1.6V-1.7V. The Vcc in this situation is noisy (with 100/150mv swings...
Hi,
I have been making a sequential channel sounding program. I tried very hard to get rid of memory leaks and now the program is able to sequentially range with three reflectors...
Hi,
I am in progress of making own audio application. I wanted to try 8_2 configuration. I see however, that despite that, 10ms window worth of data at that sample rate...
Hello. Earlier we had nordicplayground/nrfconnect-sdk docker images for v2 (e.g. nordicplayground/nrfconnect-sdk:v2.9-branch ). But it seems there is no docker image such...
I have the revision 1.0.0 of the nRF54L15-DK. I want to use the SPI pins on the GPIO header P2. The datasheet says: nRF Connect for Desktop's Board Configurator application...
