I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
I built the project on VS CODE, but it failed at the beginning
log output:
> Executing task: nRF Connect: Generate config nrf52840dk_nrf52840 for f:\nordic-sdk\project...
Hi, I've made custom boards using nrf52840. In my application I did advertise forever with interval of 200ms. Now after several weeks of tests I've two boards out of seven...
Goodday
I thought I would try the webinar
️ nRF Connect for VS Code Webinar - Hackster.io
Im getting the following error after I add Build configuration
Building...
After installing NCS 1.9.0 Open Segger Embedded Studio does not show as an option any longer. I have tried to remove the SDK and install it again, but the result is the same...
Can distance be set between nRF52840 and APP? For example, set 5m and 10m through app. When the distance between nRF52840 and APP exceeds the set distance, app will remind...
Hello Respected members, I have a question regarding the #nrf5-calendar example that is, is there any way to retain the NRF52 time after resetting the device. I am using the...
Hi there!
I'm currently looking into performing a DFU on a nRF52832 DK from an SD-Card. I managed to get the secure serial uart bootloader up-and-running and have no issues...
Hallo,
I would love to receive some support in configuring micro_ecc backend for OTA DFU.
I am using SES and following the instructions on nordic InfoCenter. The link...
Hi,
I am using nrf5280 development kit and 17.1.0 sdk.
i am working on ble_app_uart example code.
Its working fine no issue. Since the start address of the application...
We are using an nRF51x22 in one of our designs.
I am in the process of writing a bootloader that conforms to a packet format we use for loading code across our product line...
hi support team,
Customer IAC is now on GPS testing sensitivity performance. Below is from 9160 spec.
now they are trapped here for a long time. do we have any instructions...
After preforming a DFU with the nrf connect app (ios) the device advertises and will "connect" with the nrf connect app, but its not actually connected which is evidence by...
Hi, I have a project that is comunication between nRF and Smartphone via BLE and using libuartes to comunicate with 2 another devices via 2Uarts. Now I need to combine 2 examples...
I have an BLE peripheral application running on a nrf52833 with softdevice S140 were I transmit data from Bluetooth to an external CAN-controller via SPIM and back. This is...
Hi, I want to enter the DFU by setting the register.But when the sd_power_gpregret_clr and sd_power_gpregret_set are set to set the register, and the err_code is 0x02 is returned...
