Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi all,
Now, I have a troube. In Mesh 3.0, I want to advertising data. This is my function :
#define ADVERTISER_BUFFER_SIZE (128)
And whenever the data changes, I...
I bought a nRF52840 Dongle, to evaluate the use of nRF52840 for ZigBee purposes.
I have been able to flash such firmwares as \examples\peripheral\blinky\hex\blinky_pca10056_mbr...
I have a custom board where both nRF52840 and nRF52832 SOC in it.
i have flashed example Ble_Uart code from sdk15 in nRF52840 but im facing a serious issue.
i can able...
Tôi đang sử dụng bảng nrf24l01 để định vị trong nhà, nhưng tôi gặp vấn đề với định vị TOA và bảng arduino không đo thời gian nhỏ hơn micros, tôi không biết bạn có lời khuyên...
Dear Nordic,
I am trying to setup a custom BLE client service to interact with the Komoot app (Turn by turn navigation).
I can connect to the phone, and receive notifications...
Hello Team,
I am trying to run the example DFU overt TFTP, however I found the description a bit ambiguous. Seeking help to remove my ambiguity.
I am trying to follow...
Hi,
I am unable to program the nRF52 Dongle. What I see is that the "Write" option is not highlighted.
Though the Bootloader and Softdevice are already there on the...
Hi All,
I have downloaded the nRF Mesh SDk 3.0.0 and tried to run. I am trying to run the default nrf5SDKforMeshv300src\examples\light_switch\server for
Here is my software...
I have enabled the whitelist feature based on the ble_hids_keyboard example, but when I load the application it is not advertising anywhere. It is paired with my iPhone, but...
I am having one MDBT42Q device on which I am trying to flash an Example image of Peripheral to check basic functionality by nRFGO Studio.
In my device, I have sorted Pin...
i am trying to run advertising.py from pc-ble-driver-py .
i am keep getting exception from
except IndexError : raise NordicSemiException( 'board not found' ) is there...
I am looking through the BLE examples, but I can't seem to find an example that best fits my project scope where I wish to have a BLE central service that reads data from...
Hello Nordic support team I want to send command from hm10 ble chip to Nrf52832 dk board.So before I start to implement this I want to know that HM10 ble chip can communicate...
Hi, all.
I want data read from gyro sensor through i2c, and then send it through bluetooth equipment.(PC or iPhone and so on)
But i don'k know how to send gyro sensor...
I am asking about using the sd_rand_application_vector_get function; it seems that it causes my board to crash, and it never returns a success code.
I have already seen...
