Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
I am working on a linux vm 16.04 and playing with the pc-ble-drive-js library. I recently got the board up and running and started looking at the heart_rate_collector example...
Hi,
without providing too much code right away, I would like to ask how I could circumvent AT command interface hangups. My current test application calls AT commands like...
Hi there,
I'm looking forward to improve our firmware in terms of power consumption. Therefore we would like to use Power Debugging mechanism which is support by IAR Workbench...
The example projects I am referring to is located here:
nRF5_SDK_15.2.0\examples\iot\mqtt\lwip\subscriber\pca10056\s140\ses\iot_lwip_mqtt_subscriber_pca10056_s140
nRF5_SDK_15...
Hi all,
I successfully ported the Semtech’s LoRaMac-node (from official GitHub, master branch) to a custom assembly of two dev boards : the NRF52832 (Dev Kit PCA10040) from...
Hi,
I am trying to use UART interface on a nRF9160DK board to connect a rs-232 to rs-485 module for the purpose to make nRF9160DK a Gateway.
But I have no idea where to...
Hi,
Are there any known Android bugs where Android should not bond, but does? I have tried searching the web without too much success.
My central device is an older Android...
Hi,
Is it possible to add scan response with extended advertisement packet?
When I try to add scan response, then I got error NRF_ERROR_INVALID_PARAM.
I am using a nRF52840...
Hi there,
I am using two nRF52 one as Master and the other as Slave SPI, but I am facing an issue with the slave side, because when I use NRF_DRV_SPI_FREQ_125K it get some...
Hi,
I am using the nRF52840 on a custom board with SDK15.2.0 with SD S140 6.1.1.
My current BLE connection parameters are below which allow connection to the nRF Connect...
With Mesh SDK 3.0.0 , i have tested with light switch example with one client and one server, it works. My question is is it possible that one server can communicate to another...
Hello,
I have developed simple scanner application that scans for beacons (apple, nordic and of own type). It prints data about beacons over UART. I have installation where...
Hi,
due to some evaluation effort of nRF52840 Dongle, I went through whole Zephyr project building of their Bluetooth hci_uart example. After couple of ardous hours(or more...
Hi there,
To do LESC with some peripherals supporting OOB Rx, and some not, and the central supporting OOB Tx, I was wondering how to correctly enforce the OOB for the right...
Hello,
I am beginner with NRF 52 DK. I am trying to change the uart example using NRF 52 with SDK 15.02, so that I would send message after pressing button to my PC via...
