hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I have a confusion about mac address of nrf51822, I run example ble_app_uart .
When I use nRF Connect on Android, I can see the mac address of nRF51822 is CB:16:04:4A:10...
Hi,
I use nrf52832QFAA, SDK 11.0.0, Softdevice 132 v2.0.0. I need to add a device_manager_central to my project (in my project it's easier and faster than adding a peer_manager...
Hello,
In the documentation for nrf_serial_write function (SDK 14.0.0) it is written:
timeout_ms Operation timeout, in milliseconds. Pass 0 to operate in non blocking...
Hello friends,
I am trying to flash a nrf51 dk with keil5. When I try to flash it with a multilink universal I get this error:
My settings are the following:
...
Hello everybody !
My code is based on the code of the "ble_app_multilink_central" on which, I added some of the code "ble_app_uart_c" for the initialization and the event...
Hello friends,
I am trying to use the standard uart example of the SDK 11 with the nrf51 dk and trying to update the device's name via UART. I want to save somehow the new...
Greetings,
I can get the ble uart example to work on my PCA10056 using the example hex file, but when compiling the project on the SDK 15.0 S140 it doesn't work. Specifically...
Hi,
I can't found anything in the nrf52840 documentation about the ble antena directionality. I want to use it for indoor location, so i would like to know if it is omnidirectional...
I'm sending int16_t thanks to a custom BLE Service.
I receive well the data on the nRF Connect app (Android), but the data are displayed in hexa, for example for 256 I got...
Hello,
I'm developing an application that will run on a board without externel oscillator for RTC1 and it means no app timers support.
I started from ANCS example and...
Hi, I tested to run BLE Mesh(v1.0.1) light switch example using SEGGER embedded studio(SES) on Windows10 and three nRF52DK(ntf52832) boards .. one client, two servers. It...
Hi,
I encounter the problem when using the mcuboot with zephyr 1.11 is that the system keep rebooting.
mcuboot: https://github.com/runtimeco/mcuboot
mcuboot build...
Reference: bbc micro:bit (microbit) board Eagle schematic files
I heard that bbc's micro:bit board is based on Nordic's nRF51822 & build by Nordic Semiconductors
Since...
Using SDK14.2.
I'm trying to optimize the throughput of my ble_nus-based app (I'm getting about 5k/sec right now). I've read elsewhere on this forum that increasing NRF_SDH_BLE_GAP_EVENT_LENGTH...
