Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Hi
I am currently using SDK 12.1.0 with SD 3.0.0.
I want to add the option for serial DFU, which was added in SDK 13.0.0.
I wonder if I can implement the serial bootloader...
first of all many many thanks for nrf sniffer 2.0 and all of it's improvements (linux, live data display, easy install ... etc)
i'm sure there are still a lot details missing...
I am trying to use the nRF Connect v1.0 RC with the pca10040 board. I followed the instructions of your [page] and when i open the serial port i got an error (Error occurred...
I am using nrf52832_xxaa with SDK v11.0.I tried writing into the APPROTECT register by using the code below
sd_softdevice_disable();
NRF_NVMC->CONFIG = (NVMC_CONFIG_WEN_Wen...
Hi, as per subject, I would like to know the trade-offs of using the internal DCDC vs LDO when it comes to RX sensitivity specific to the nRF52840-QIAABB variant.
From this...
Hello,
I am using the nRF840 PDK for testing the radio communication.
During my tests, for TXPOWER=0xD8(at minimum), I found a gap of 7 dBm between the radio output...
Hi, I am trying to connect the nrf52840 to GPS module, and I hope that the dk could read the GPS information via UART. I try to modify from this example nRF5_SDK_14.2.0_17b948a...
Hi,
the following are the TX's current consumption for 0 dBm from the datasheet:
I assume the second line refers to the measurements when the internal LDO is used...
Hello,
I know how to update the application through OTA at the moment, I do the following steps:
set the device run in DFU mode by writing 0x01 in Experimental...
Hi, Nordic engineers
I checked there is one error function in nRF5_SDK_12.1.0_0d23e2a:
in nrf_esb.h
uint32_t nrf_esb_get_rf_channel(uint32_t * p_channel);
but in...
Hi,
I have 3 nrf51822 devices. Two of them act as peripheral and one acts as central. Each peripheral is used in a wheel and they are the 2 wheels of a cart. Central is...
The latest Objective Spec nRF52840 Objective Product Specification v0.5.1 got me a little confused since I was working off of v0.5 until few weeks ago. My application is a...
I'm using SDK 12.2 with Softdevice S132 V3.0.
I try now the migration to the most resent SDK 14.2 with its Softdevice, because it seams there were several bugs fixed in between...
I am trying to use a dht sensor and arch ble device to display temperature on the console. But when I flash the program on to the board, I cant see the output on the console...
Hello Everyone,
I have developed my application using BLE for connect android mobile. I have design complete PCB using your reference design. But i have littele confused...
