hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I add the NUS in the ble_app_hids_mouse example which the sdk version is 14.0.
There are four services in the project: dis, bas, hids and nus.
When I connceted the...
hi all ,
I am looking out theory about SM layer in BLE . I read CoreV5.0 but I do not understand much about pairing , bonding , STK , LTK . Can you give me some document...
Can the link between two devices communicating with each other via NRF24L01+ be improved by using Tx messages with no ack (W_TX_PAYLOAD_NO_ACK) instead of messages with ack...
Specifically, sinking a Cree C503B green LED (Vf 3.2V at 20ma) from a GPIO configured for high drive, without a current limiting resistor, from VDD 3.6V?
Figure 23 “GPIO...
Hello All
We are using nordic thread sdk's sample simple coap client and server.We want to ON/OFF LED of coap client from coap server.
Can any one help how we can achieve...
In SDK13, the initialisation of the low frequency clock used to be done within sd_softdevice_enable . In the SDK14 version of nrf_dfu.c , the LF-clock is already initialized...
Hi, I want to use the AES-CCM of nRF52832. But it can not work with the softdivice. I have read the following question and answer.
https://devzone.nordicsemi.com/question...
Hello All,
I have a peripheral device where one service with 4 characteristics is implemented.
Out of these 4 in 3 services notify is enabled.
Now I want to subscribe...
I have a situation in which a central device (A) must be able to receive from a power constrained peripheral (B) with very low latency, but likely at long intervals.
To...
Dear Nordic,
I tried to download the new SDK nRF5-SDK-for-Thread from here:
www.nordicsemi.com/.../60504
However, when I clicked on it I only got the TTM 0.11.0.
...
Hi every one ,
I am using NRF51822. I download the code
from this link. github.com/.../nrf51-ble-tutorial-advertising
I able to flash the hex file & see board are...
hi~
i am working with nrf 51822 with custom board and softdevice s110.
i am using is7020-a20 temperature / humidity sensor via twi (i2c)
i tried 2 versions of twi example...
I followed this guide , I'v managed to run make files and flash them using the terminal, then when trying to build the project in Eclipse, I get this :
Make: no rule...
Hi,
I am following the "Bluetooth low energy Services, a beginner's tutorial", however, this tutorial is written for SDK V11.0.0 and I am using SDK14.1.0, softdevice 5...