hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I am use Exclusion list for my one application.
Exlusion list work is ok,but i am facing problem for how clear Exclusion list ?
My Controller: nRF514222 Rev 3,...
This is my first time working with a microcontroller and working with C as well, my only previous experience being C++ done in notepad on Linux. Currently I'm trying to just...
To reduce nRF52 design thickness, I'm planning to use a low profile inductor on the DCDC converter.
The low profile inductor has a higher resistance, compared to the recommended...
Hi, All.
Once I wrote data in NV memory, it's OK. I can get the same data I put in.
But, after power off - on reset, data are invalid. It's all 0xff(erased state).
I used...
Hi,
I have been trying to do it and even though I have generated packages using the old nrfutil and the new 1.5, when I use nRF connect to do the upload it aborts without...
I programmed my beacon with this code:
ble_app_beacon.zip
I use nrf connect app to see its signals. nrf connect can find my beacons but it says:
serviceUUID : N/A
TxpowerLevel...
Hi all,
I believe it should be possible to defined a characteristic which can be written to but have no automatic write response ACK sent. Instead I want to send a manual...
I develop a temperature sensor sending a temperature and battery status every second.
Used to work fine on previous nRF Toolbox.
Today on my Android 6 and latest nRF Toolbox...
Difficult to obtain the high-ohmage resistors in the solar beacon reference design. Will 5% resistors suffice or do the resistors have to be 1% tolerance.
I have difficulties understanding the COMP APIs, this function below starts after initializing the COMP the peripheral.
nrf_drv_comp_start(NRF_DRV_COMP_EVT_EN_CROSS_MASK...
I am using the nRF51822 utilizing the internal LDO setup. I received a question during regulatory submittal that I am not able to answer and am looking for help on. Is the...
Hi
I've tried to update some of our environment to the SDK12 files. When I tried to compile some of the files a weird bracket error showed up.
At the end i could find...
Hi,
I'm trying to run one of the template app programs from the Nordic SDK 12.0 library with a nRF52832 board as my target. I had trouble with compiler errors using the...
I curious about that what does exactly mean 'arm5_no_pack' folder name in SDK.
I usually used or developed under uKeil5(MDK-ARM5 v5.12).
What is relation with 'arm5_no_pack...
