I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hello,
I started with the UART timeslot API but countering some problems.
It will be helpful if I could get any tips or solutions.
I am trying to sample every 2ms and...
Hello
I asked a follow up question on another user's posting on devzone.nordicsemi.com/.../ , but no one seems to respond, so I will try here.
The abovementioned posting...
I've run ble-sniffer_win_1.0.1_1111_Sniffer.exe and pressed CTRL-R, then I get:
Keyboard input error: [Error 2] The system cannot find the file specified..
The log file...
Hello
I am developing an application where the data troughput is very important.
As i understand, the data thoughput is dependent on the connection interval and the number...
Dear developers,
I have a problem with peer manager reporting PM_EVT_ERROR_UNEXPECTED right after it has reported PM_EVT_CONN_SEC_SUCCEEDED.
This is quite a long call...
We all know that PPI can have the same event to trigger other tasks.
But I couldn't find any official document explaining the priorities/timing of those tasks linked to the...
Hi
I am trying to put the nrf52 device to system off state, in order to get minimal current consumption.
When I don't use the soft device, and enter system off state by...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
If i scan again when it is scanning, system goes halt and reset.
So i want to check it's scanning or not before I make it scan...
We have an RFID application, the tag sends the 10 byte data and the data is read at the Receiver continuously thorough SPI channel to MCU.
Payload of 10 bytes, Enable CRC...
I've been playing around with the multi-central central/peripheral examples and I thought I would modify the peripheral to instead use a service I had written for another...
Hello, I want to detect the any activity of the ADXL 362 and blink the LED ON and it should also detect the inactivity to turn OFF the LED.I am able to generate the activity...
Hi,
We are using the Nordic Semi nRF51822-QFAA-T to do BLE project, but when we test CE/FCC RF test(Conducted / Radiated), there has a lot of noise around 2.4G.
BTW...
Hello,
I try to find the information if there is a softdevice (for nrf51 or nrf52) that supports "LE Secure Connection".
In general, where can I find which bluetooth version...
I'm lost.
Can someone point me to place or the best example of how to send data (any) from NRF51882 to iOS app when app is in background.
Is it possible at all ?
I'm trying out the ble_app_gls demo with the Nordic Master Control Panel app (on Android). What I see is that the MCP can connect to the device without bringing up a pairing...