hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
hi,
i have a timer which is being called each second. when i give timeout less then 1 second then the code executes properly and goes to event handler. but when the timeout...
Can you tell me how to integrate this library so that my code works with it? I'm new to using both these OLEDs and Nordic Semiconductor based devices. THanks
I'm trying to write a firmware for PCA10001, which works like a bootloader. In other words, it can download some data into the Flash. To avoid conflicting with the existed...
Hi thank for reading with your kindness
I used keil with nrfready_desktop_2_/* files
when I clicked "Start/Stop Debug Session" with simulator in debugging session, ...
HI,ALL
i notice that the buttons_leds_init is initiating the bsp function.
just like LED and Buttons.
uint32_t err_code = bsp_init(BSP_INIT_LED | BSP_INIT_BUTTONS,...
I recently purchased nrf51-DK. I was going through a getting started document which said to update the firmware on the board. After updating it the boards just keep disconnecting...
Hi:
There is a worried question around me.
when i put my product and phone in a firm place after the product connect with APP of phone.
I find that there are lots of...
L.S.
For our products we have chosen to use the RFDigital RFD22301 (previously RFD51822) product which has a nrf81522 chip inside.
Last year we discovered some issues...
What are the S130 SoftDevice v2.0.0-7 alpha iROM and iRAM settings for the nRF51822 and the ble_app_hids_keyboard example?
Someone at Nordic Support suggested the following...
Hii Nordic guys,
I'm trying to test the example project examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay so I just compiled and trying to flash on...
Hello
I am developing an application with BLE and I have just faced to a problem.
I want to check my IDE settings and development environment.
I am using the development...
A good problem to have... we're only seeing 300nA current draw with a 3V lithium primary while in SystemOFF on the nRF51822, using LDO.
Is that correct? We've measured...
HI , ALL
i added a event in the function 'on_ble_evt' like followings:
case BLE_GAP_EVT_ADV_REPORT:
printf("Start Advertising\r\n");
break;
At first i think...
Hi, I mostly use the SDK 7.2 or SDK 10 and S110 7.1 or 8.0
since I have multiple custom boards that uses revision 2 and 3 chips.
My custom board I'm about to use has...
I want get an interrupt from the ADC after every sample (oversampled by 4, so burst is enabled). This works fine with EasyDMA, but I want to be able to not use the EasyDMA...
