Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
I have developed the schematic of connecting NRF 8001 BLE chip with Arduino,the file is attached that contains the schematic. Can you please verify my schematic i.e will it...
Hi, I'm looking for a solution can make a ble device communicates with multiple 2.4g devices at the same time , is 51882 qualified for this? or just by combining both nrf8001...
Hello,
I would like to use the fifo common library but i have an link error. I don't understand that because fifo_app.h is included and contain the functions...
...
Hi
We are using indication to send data to make sure master receive all the package.If we didn't
receive the confirm message,what should we do?Should we send it again in...
I'm guessing it is because the engine powering the site does not support it. But has it ever been considered?
I think it is a powerful way to engage users and build a community...
Hi,
I have two questions about nRF24LU1+.
Q1
Can i change nRF24LU1+ isocheonous endpoints(Endpoint 8 IN/OUT) to Endpoint 1 IN and Endpoint 2 OUT?
Q2
Can i use Endpoint...
Hi,
we’re a group of students at NTNU in Trondheim doing a project regarding bike and pedestrian registration. So far we want to make a solution based on iBeacon and Bluetooth...
Hello,
I am looking into the possibilities of implementing frequency hopping using the nRF24L01+ radio with an external Ti MSP430 microcontroller. I have read that it's predecessor...
Hi,
I want to realize the function of bond, I use "lib_aci_bond(180/* in seconds */, 0x0050 /* advertising interval 50ms*/);'\",.When I click the connect, it can connect...
In nrf51_sdk_v4_4_1_31827\nrf51822\Source\console\console.c,
#include "uart_legacy.h"
But there is no "uart_legacy.h" file in the SDK.
I have to modify to "app_uart...
I downloaded the source for the Android UART app, hoping to hack it into something I can use to test my gadget. But it's incomplete: it fails with the message:
Missing...
I have 3 short questions:
Does S120 support or will support swiching over BLE and Gazelle like S110 does?
Will be able in future to be connected to a BLE...
Hi,
If I want to send data(400Bytes) to client(phone),I must use sd_ble_gatts_hvx to notify client. Is it right?
Every time I notify 20bytes until the end, is it right...
