hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
When I get a custom board, how do I detect and flash it? I have three options on the board:
I have a USB cable with:
GND
D+
D-
+5V
OR can configure the usb...
Hello, I'm trying to get nrf5340_audio example running on nrf5340 audio dk.
I'm able to build the code and run it however i'm unable to bond with my mobile phone with android...
Hi! In order to get more accurate battery SOC measurements I need to provide a custom battery model to the app. So, I had to use the nPM1300 EK + Fuel Gauge board to profile...
Our device is set up to provide AT Commands directly to nRF9160 using a USB UART connection and control using a VT100 Terminal simulator. When attempting to connect to the...
Hello. I'm using npm1300ic. In one example, there is a battery_model.inc file related to li-po 3.7v 200 mah battery, and the battery you are currently using is li-ion 3.7v...
When dynamically allocating BLE GATT services and characteristics using custom structures and Zephyr’s dynamic memory functions (e.g., k_malloc, k_calloc), the service registration...
Hello Nordic team, Whilst porting our product from nRF Connect 2.4.1 to 2.9.1 we encountered the following problem. When compiling with ZIGBEE_FACTORY_RESET=n we get Seems...
I'm new to developing nRF devices. This is the first time to set up SDK.
I installed Toolchain Manager v1.2.6 to install SDK, but it is too slow and falls into error. It...
i'm looking for an extremely simple BLE beacon app, which advertises (say) at 1HZ and then enters a "low-power" sleep mode....
there are numerous samples included in the...
Hello forum ,
In here i will upload my project in zip where i m using w25q64 flash -nrf52840 .i m trying to read data of qspi flash read write and read for an two byte(trying...
I am in the process of integrating a custom display driver (ST7305) into my Zephyr-based project and have followed the necessary steps:
Placed the .c and .h source files...
I'm using SDK version 2.9.0 with an nRF52840 in a combined peripheral / central application.
The nRF52840 device starts advertising, but then after connecting (as a peripheral...
Hi,
I am trying to download the nrf connect toolchain in vs code but getting this error
Error: Failed with exit code 1. Failed to download toolchain bundle Caused by...
Hello.
I am developing an application based on IOS-nRF-Mesh-Library, and currently considering porting firmware upgrade function of IOS-nRF-Connect-Device-Manager for updating...
Dear All:
I don't have a le audio enabled phone, and i want to study the hci commands about cis and bis setup up processure.
Could you please provide some HCI logs from...
