I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hi All,
I'm using nRF9160DK PCA10090 Version 0.9.0 and I want to update the Cellular Modem Firmware using nRFConnect 3.8.0 Programmer v2.0.0. Debug Probe is switched to...
We have a timer with a number of variably sized intervals as illustrated below operating on a single capture/compare channel (CC):
Currently the method we use to set the...
Dear all,
In the datasheet and online it is mentioned that the DAP (Debug Access Port) is activated when a programmer is attached. Moreover, it can happen that the programmer...
Hello all,
I am trying the get working the example project nfc_writable_ndef_msg on a nRF52832 with the nRF5 SDK.
I have tried the others NFC examples were most are based...
Hi I am trying to update the connection interval of a peripheral device (nRF52840 ) and I have followed the steps mentioned here .
After Enabling the ble on the device I...
Hi Team,
I have several nrf52840 developing boards for developing BLE Mesh applications.
Now, I want to use SPI interfaces. I didn't find any instructions or examples...
Hi
I am struggling with timer in counter mode. What i need is the counter to calculate time between each loop in microseconds. I do not want time interrupts i just need...
I am currently writing code to read the battery voltage using the C language. I would like to include the header file "es_battery_voltage.h" and use the two functions "es_battery_voltage_get...
We are using the 52840 chip SPI interface in slave mode and communicating at about 8MHz are noticing that during periods of innactivity with all systems stopped and sleeping...
I tried to install the nRF Connect for Desktop v3.8.0 on my PC with Windows 7, but it does not connect to DK PCA10040. The nRf studio work fine with my DK. Then I install...
I am getting starting the nrf52832 board with an LSM6DSL sensor for motion recognition. it is possible in edge impulse ??
how to configure the firmware Development and how...
Hello.
I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
When making a BLE connection, you will receive an advertisement first. Then SCAN_REQ...
Hi Nordic,
I try to find an API to set the duplicate filter when scanning. But I found nothing.
I want to use the dulicapte filter disable feature to improve searching...
Hi. I've been working on getting a gsm modem functional using the GSM Modem Zephyr driver on an nRF5340. I believe I have the overlay file setup correctly, but am recieving...
