I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello again Nordic Pros,
I am trying to get some debug logging going using the 52DK running ble uart central under SDK 12.3 and RTT Viewer v6.4.
I have setup config.h...
Hello, I do connection between one nRF52840 (central / NUS) to multiples nRF52840 (peripheral NUS)
in my function static void on_adv_report(nrf_ble_scan_t const * const...
Hi Nordic Developers,
I would like to extend my question on creating vendor specific model from this question I posted earlier (extension of Thingy Mesh Demo v0.1):
https...
Hello Nordic Pros,
Doing some debugging using RTT Viewer and an nRF51822 under SDK12.3. Here is the code lines of interest:
And here are the log messages:
iDrink:...
Good afternoon!
We're considering an off-the-shelf nRF52832 based device for our needs.
the application will likely involve two nRF5283-based devices fitted with external...
Dear All,
On the http_application_update after the download is complete, in order to run the new firmware the user needs to press the reset button.
I would like to be...
As in another post , I was looking for a way to change the TTL per message. Is there a reason that it can only be changed per model? I can imagine the TTL being part of the...
Hello,
I'm trying to use the mesh DFU on 2 nRF52840 DK by following the quick start guide and it didn't work.
Using the mesh sdk 2.0.1 I made the below batch file as described...
Hi,
We need a BLE chip which can be used as a radio which supports BLE SIG mesh and work on standard HCI commands.
Kindly suggest the right device.
Thanks & Regards...
I am using a Mac with SES installed. I created a DFU example and downloaded it to the Thingy 52 to see how it works. That all went fine. Unfortunately, it has disabled the...
Hi all, I'm trying to evaluate nRF Connect SDK, starting with guide in nRF Getting Started Assistant app. So far I've executed every step, but when I try to open the project...
We are using nRF52810 and SDK 15. We have to save up to 50 bonding information.nRF52180 is knowing to save up to 4 bonding information. Can you save up to 50 bonding information...
Hi,
we are trying to use FAT file in nRF9160. Referring the test case in "ncs\zephyr\tests\subsys\fs\multi-fs\src" to mount the FAT file.
But getting an error like "ff...
