Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Good day.
We recently bought the NRF52 DK and the Power Profiler Kit with the intent to log power consumption of our battery powered products. Before purchasing the products...
Hi,
I tried nrf connect and nrf hrs example. I used nrf52DK. I bonded the device, and connected with autoconnect. I turned off the nrf 52 DK, and turn on. The nrf connect...
I am using the secure bootloader with DFU, and the buttonless DFU service. I extracted these applications from the Thingy SDK v2.1.0. This works perfectly fine as long as...
Hi,
My problems are as follows:
SDK :nRF5_SDK_15.0.0_a53641a.
IDE:MDK 5.2.6
Chip:nrf52832 SPI0
External Flash :W25Q64
Now ,I can read the chip ID correctly ,but...
Hi,
Please find following source code.
After compiler by Keil 5.24.2, some code will not compiled,
I can see the situation by "enter debug mode, please find following...
Hi,
I am trying to develop a central device that would scan for devices that start with a prefix XYZ_, for example XYZ_1111, XYZ_1245,...
Is there some way to add a name...
Hi,
I am using esb function to implement my project, and I set "noack" condition to "true".
How can I know the destination address when I receive a packet?
Thank you...
I need to add ARM_MATH_CM4 to my preprocessor definitions using Segger Embedded Studio.
I know this has been dealt with in "nRF52832: How to Include the "arm_math.h" library...
We are developing a BLE device that will act as a central and send data to a peripheral. To begin with, I have used the uart central example code from SDK to set up a central...
Hi, I am trying to figure out the adc example posted by Nordic Semiconductor on Github.
https://github.com/NordicPlayground/nRF52-ADC-examples
There was two examples,...
Say I have the PWM Decoder set to NRF_PWM_STEP_TRIGGERED. If I use NRF_PWM_TASK_NEXTSTEP to step through a PWM sequence, will an event be generated for each step? I would...
Hi,
I have merged ble_app_multilink_central example and ble_app_uart_c example. and function is Ok.
Central(nRF52) can connect to HM-10(ti cc254x) and communication is...
Hello
I am trying to do BLE communication using BLENano2 (nRF52832) now.
Therefore, using SDK 15.0.0, we are writing a program with keil u5.
BLE communication can...
Hello!
I am using SDK 15.0.0 with keil.
I tried to use the sample program to do BLE communication, but I have one thing in doubt.
I'm using SDK15 / example / ble_peripheral...
I’m in the process of learning the nRF52, and tries to combine the ble_app_gatts and the pin_change_int examples (using nRF52 DK, SDK 15.3 SES projects on a Win7 machine)...
