hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I have downloaded both "nRF5_SDK_15.0.0_a53641a" and "thingy_sdk_v2.1.0".
After that I tried to build the "main.c" file of " thingy_sdk_v2.1.0" in keil uVision5 but it showed...
My nRF52840 custom boards seem to be unable to boot without RTT viewer started of JLink commander connected.
The hardware configuration is taken from the nRF52840 PS 1.0...
I'm currently trying to update data periodically in the advertising response packet. After successfully initializing and starting advertising, I configure srdata within a...
What is the difference between setting a pin output (to drive an LED) with this set of commands:
nrf_gpio_cfg_output(5);
nrf_gpio_pins_set(5);
and this set of commands...
i use sdk14.2 52832 i use uart
UART0_CONFIG_USE_EASY_DMA =1 consumption ~2.1mA
UART0_CONFIG_USE_EASY_DMA =0 consumption ~650uA
Is this a normal phenomenon, is it true...
Hello !
I'm Omar Rosas from Newark / Farnell tech Support.
I have a customer that he need's to know if there is a enclouser or housing for this part number NRF51822...
Hello,
Few days ago our CI builds which were written with Mesh SDK 1.0.0 started failing and it turns out that 1.0.0 was removed from https://www.nordicsemi.com/eng/nordic...
What is the ID for indicating that NO SD is required in a DFU pkg?
I am using SDK15 with a secure UART bootloader, but NO soft device. (just MBR, APP, BL & BL settings)...
Hi there,
we are currently designing an NFC antenna for our product based on the NRF52840.
The integration guide out of the spec is pretty comprehensive (see below)...
Hello everyone,
I would like to update my advertising data on the fly but actually it doesn't work. Some posts talk about this behaviour but no real answers.
Here's my...
Hi everyone.
In our products I am using the dfu bootloader included in the SDK 10 with very minor modifications affecting only what is advertised. Within the bootloader...
Hello!
I am trying to implement the Cycling Power from https://devzone.nordicsemi.com/f/nordic-q-a/9169/cycling-power-service-0x1818
Please, could you show how we need...
Sorry I am reposting this issue as by mistake I closed my previous question.
Hi, I have following issue and need some help. I am using SEGGER Embedded studio for ARM Release...
I used the command
nrfjprog -f NRF52 --program light_switch_proxy_client_nrf52832_xxAA_s132_6.0.0.hex –-chiperase
to programm the nrf52832 board and get the below...
Hello,
I found the strange phenomena on nRF52832.
By using the SAADC, I have some noise on ADC Data only at a certain temperature range.
Temperature range is depend...
