Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi triying to drive a Relay with Output but have tried every functon in "nrf_gpio.h"
this works with a LED perfectly :
nrf_gpio_pin_toggle(23);
in the main i configure...
I am currently working in the " ble_thread_dyn_mtd_coap_cli" multi protocol example.
Whenever I call printf my program crashes.
I think it has to do with the ble_nus service...
Dear friends,
I am trying to run the PWM in my project. I have:
added the PWM driver successfully (4.0.0-2.alpha, nrf_drv_pwm.c, nrf_drv_pwm.h) ;
set...
I tried porting app from pc10028 to pca20006 by copying the main file from pc10028 ble_app_uart to main file of ble_app_beacon of pca20006.I resolved all the #include related...
hey
I have a nRF51822 eval board and I want to use it as hid keyboard to send some media key
such as vol+/- play/pause, etc. I have used the example code ble_hid_keyboard...
Hi,
I develop a program using arduino primo,
and i want to layout a new pcb board with new nrf52832 chip.
The new chip may not have any bootloader.
What kind of method...
Hi
In our Nordic SDK ble_peripheral projects , It almost support following boards
1. pca10028
2. pca10036
3. pca10040 .
I want to port in pca20006
May I know...
I am porting a C++ project that was using version 6 of the SDK to version 14.2 (big leap, I know). I want to use all the new bells and whistles from the new SDK that makes...
I am using power profiler with nRF52840 SDK. And I have measured the current of the board. But I want to calculate the energy consumption of my program. How can I get the...
hi ：
I want 4 channel PWM output, the following code doesn't work, I want to know where is wrong
#include <stdbool.h>
#include <stdint.h>
#include "nrf.h"
#include...
Hi,
I would like to control gpio pins in micro seconds with timer,
I know that it is very difficult to implement with only timer owing to soft device (interrupt handing...
Hey Dev zone,
I flashed my application onto my Nordic Thingy board (through Onboard Jlink debugger present on nrf52840 dev board), and can see some pretty colors (LEDs...
I am seeing some significant temp fluctuation for the temp sensor on the thingy to the tune of +-1 to 2 deg celsius. This is when placing the device in a closed, sealed container...
