I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
Is the BLE mesh light switch example of a server and client model the correct implementation for our product?
Our product will include from one to ten devices. For a customer...
Hello,
The question might be a little vague at the moment but I would like your guidance if possible.
I already asked other questions related to this topic but I will...
Hello,
I have been seen some resets on my softdevice v3(SDK12.2) that I am unable to understand,I am using the FPU as well as pheripherial as SPI, I have set up SystemView...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Does increasing the sample time on the SAADC increase the accuracy of a single shot measurement on the SAADC? I couldn't find anything in the datasheet regarding accuracy...
Hello,
I would like to use nRF52810 chip.
And I want to implement PCB trace antenna and PCB chip antenna on same PCB(for provision)
Either PCB trace antenna or PCB chip...
I am using the SPI peripheral for communicating with a network through long wires. Is it any information about the impedance of the driver outputs from the nRF52832?
I will...
nRF52840 OPS v0.5.1 section 16.16.2 states “A pin reset is generated when the physical reset pin on the device is asserted”. This seems to contradict the descriptive name...
Dear Nordic
All our last SDKs in "example/dfu" have same error.
Code is not corect:
nrf_clock_lf_cfg_t clock_lf_cfg =
NRF_CLOCK_LFCLKSRC;
Impossible properly...
Hi Nordic Support,
According to the answer in question:
devzone.nordicsemi.com/.../
it is not possible to update the bootloader (which is the case with "bootloader_secure_ble...
I am trying to set up RTC2 by following an example
github.com/.../saadc_low_power
I ported it to my project which is running a softdevice on nRF52. It works perfectly...
Hi Alls,
I'm trying to compile and test the example project from SKD_12.3.0 and receiving the following error:
#error app_timer for freeRTOS requires configUSE_TIMERS...
Hi everyone
I'm doing some basic test to verify the correct platform for a future project, we need ble long range, therefor we are testing the NRF52840-PDK
I have loaded...
hello,we use nRF24l01+ for the communication of IoT.There are a lot of terminals work at a same channel,when the controllers send CMD,we have found:the length of reading from...
