Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hey all. I'm working on a really simple beacon application and I'd like to use RTC0 when the BLE stack isn't using it... is that possible? No BLE connections, just 1 advertisement...
Hi,
I'm facing a weird problem resulting from the following code:
while((!twi_tx_done) && timeout--);
The main file and the MPU9150.c which includes this command...
Hi, I try to capture ipv6 over ble packet.
So, I construct system like, nrf dk 51(with sensor) - rasp
nrf-dk 51 is equipped with coap-server source and rasp doing like a...
Hi everyone,
I have a really weird problem.
I created a makefile based on Nordic's example from the app_template and created 2 additional targets, one called "debug" and...
I have upgraded my laptop to Windows 10 and all hell break loose.
When I either connect the board or the dongle, they are stuck in a loop of connect/disconnect behavior i...
hi,
i am using ble_uart example in which i am sending 3 byte of midi data
(90 1e 45 0a .E.)
i am getting (.E.) when i converts this ascii value to hex value i get (2e...
Im trying to provide DTM functionality for certifications tests. I can't setup an UART interface, I found the below code which tries to use DTM without UART. it uses channel...
Hello,
I've read a lot about trouble people had when they used bluetooth and flashed the rom without using the propper softdevice APIs.
What is the issue with concurent...
Good morning.
I ´m working with nrf51-dk, sdk 9.0.0 and softdevice 110.
I have done a proyect without softdevice, only uart and master spi (mode 0) and works perfect...
Hi, I flashed the Proximity Application to nrd51822,with s110_nrf51822_6.0.0-5.beta.
the chip run right, and I used the NRF Master Control Panel, when I write data 0X02 to...
Dear all,
I have tried using a setting a break point in main() of my program. Without running the softdevice, it is fine to pause in the break point and continue to run...
Hi,
I am developing a product using nrf51822. While pcb designing I am getting a clearance error. Please let me know how to resolve it. All the dimensions are 8mil in clearance...
Hi,
I am editing my question:
I have seen some strange behaviuor I could not explain. In order to test it I have made the next test program:
I am using the application...