Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I'm using SDK 9, I flashed the softdevice 8.00
I compiled the project located in \SDK_9.0.0\examples\dfu\bootloader\pca10028\dual_bank_ble_s110\arm5_no_packs
I flashed...
Hey,
I am trying to use app_timers and nrf_delay_ms together but the system gets stuck almost everytime. I have the following code:
void timer_handler(void *p_context...
We have noticed an issue when using the UART on our nRF51822 (SoftDevice = S130, nRF51_SDK_9.0.0_2e23562). Our Nordic app waits for commands on the UART and processes these...
Hello Everyone
I am trying to configure the two GPIO in High Drive mode 5mA but after compiling the program it does not seems like congifured to High drive Mode because...
Hello, I am designing a system to transmit a mono or stereo audio signal over RF, a few hundred feet, then receive it and reconstruct the audio and listen to it on a speaker...
I am developing a HID keyboard with SDK v6.1, SD v7.3, IC revision 2.
The keyboard is already able to advertise (non-whitelist) and bond with iPhone, and connect/reconnect...
Hello
I want to optimize SPI com as fast I can do:
First I am using the fast spi data rate by SPI_FREQUENCY_FREQUENCY_M8 variable and I want to reduce at first the timing...
As far as i understood it supports 4.2 BLE because using it i'm able to see packets between nRF52 central and peripheral boards (HRM example). Is it so?
Question:
I am confused about who can do (or rather who usually does) whitelisting - the master or the peripheral device?
My findings so far:
I can't find a certain...
Hi,
I have written a windows 8.1 application to connect to my custom nrf51 device. It is used for configuration and is set up without requiring a password (I do not need...
I want to be able to transmit the on-board temperature and battery voltage over a beacon application. The application only needs to transmit periodically similar to an iBeacon...
Dear,
I'm now face problem on button interrupt.
I use 3 buttons for my system.
button 2, 3 is used for boot diagnostics. assigned as below.
bsp_event_to_button_action_assign...
I'm trying to lighten the leds using ble, my problem is that when I measure the current consumption when the leds command sent, it reaches to 5mA which is not suitable for...
Hi
I've playing around with the new peer manager a while. I used the example "ble_app_hrs_rscs_relay_pca10028.uvprojx" from the SDK10. After a first fix (see Link ) in...
Hi,
I want to use timer1 or 2 interrupt ISR to generate complicated PWM signal.
but the timer->intenset setting cause ble connection drop problem.
Please refer to my...
