why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Dear Sir,
After I remark this //BLE_GAP_CONN_SEC_MODE_SET_OPEN(&cccd_md.write_perm); and program it into nRF51822, then I cannot program it again. PC program report it...
I have modified the included HID mouse example to allow for left/right/middle mouse clicks. However, it is not clear to me how to set an event handler for both when a button...
What is the recommended PCB thickness of the nRF51822-QFAA Reference Layout? It'd be great to have a specification in the package including the full spec of the PCB material...
Hello Folks, I'm starting some work with the nRF51822 Evaluation Kit (PCA10001), but have very quickly run into a blocker when trying one of the ble samples. (I've previously...
With Soft Device 5.1.0 I generated the binaries from the hex by doing:
arm-none-eabi-objcopy -Iihex -Obinary --remove-section .sec1 --remove-section .sec2 s110_nrf51822_5...
Dear support,
We are in the design stage for a BLE application. We looked at different options. Although the NRF51822 seems better in specs. The TI parts CCxx offer this...
So far I have made a successful program that utilizes BLE to send and receive radio signals in Kiel. But I have only been testing this program by using the provided Master...
I just entered a Case to Nordic with this same question but do not expect to get a response over the weekend so I am posting here. I made the assumption that the Nordic Cases...
Dear everyone:
Now,I have a project which use Nordic product solution to developemnt.
And , We need your company to provide some information and solution.
(like,have...
What is the maximum value of RSSI parameter for nrf_gzll_device_tx_info_t structure?
I have done a test on RSSI parameter value return in nrf_gzll_device_tx_success callback...
Hi Nordic
I don't fully understand the drive settings for the GPIO. For example S0H1 means when the pin is CLEARED, it will use standard drive (can sink 0.5mA) and when...
Hi there,
i was trying to implement a firmware for a small device using the nRF8001 only in broadcasting mode.
So far, everything works fine. But one thing mentioned...
I'm happy with the status of my app on the evaluation board and I'm ready to start downloading it to my target board. I plugged the Segger J-Link Lite CortexM board into one...
