why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hello all,
I have realized my own board with a msp430 microcontroller and a nRF24L01+.
I have configured my nRF24L01+ as described in annex C of the datasheet; the objective...
Is it possible to use the J-link to debug a stand-alone PCA10004 ? I am not using the motherboard. Powering the board separately. When I try and run debug in Keil I get error...
I would like to ask a question about the time of :"Time between DISABLE task and DISABLED event when
the radio was in TX" of the "Jitter". In the picture show the "Jitter...
Dear nordic guy, I'm developing
with nrf51822. I have one question regarding main clock control.
I want to turn on and off 16Mhz clock in application side.
application...
Hello,
I have some code running that transfers binary data from an iPhone to a nRF51822 device (used for firmware upgrade).
I have used a variable length characteristic...
When starting with nRFgo Studio "Erase all", "Program SoftDevice" & "Program Bootloader" to have a almost virgin base without an application, I succeed perform an over the...
Hello,
currently I am thinking about the proximity concept. The following scenario is given:
We have a Display that shoud lock/unlock a Device
We have a iPhone...
I used SDK 5.1 and S110 6.0, I dowmload the project ble_app_ancs to nRF51822 DK. I try to connect it to iPhone 4s (which run on IOS 7.04), when I click 'pairing', the led...
Device: NRF51822; BMA250E
Description:
When I read BMA250E via I2C without BLE protocol, commnucation run well.
And if there is no I2C commnucation, BLE protocol can...
Hi all,
My questions are related to frequency on the soft-device firmwares for nrf51822.
In S110 does the frequency channel hop according to the CONNECT_REQ packet...
Hello,
I am testing the ble_app_hrs project on two eval boards, with s110 and s120. Everything works.
If I power-off the peripheral board (s110), it seems that the master...
Dear Nordic guy, I'm developing with nrf51822.
I have one question regarding flash write.
In ble connected state,I have some error to write some data to flash.
I want to...
Hi,
I just loaded the nRF8001 Arduino code on my board and used an iPhone 5 to read the data that was being advertised. I get the following response:
<CBCentralManager...
