Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
Hi,
I am running some tests with the long range example provided by Nordic and observed this behavior which I can't account for.
https://devzone.nordicsemi.com/nordic...
path:
\experimental\cli\cli_agent_router\pca10059\mbr
When I execute "bdb start" in the serial port and then execute "bdb Legacy Enable", the terminal devices that are...
Hi,
I report some problems.
I have been using keil5,it work well. Because nRF Connect SDK doesn't know Keil
now i have used Segger Embedded Studio for a period of time...
Hi everyone. Here is my code for 2 different timers that put uc to sleep and wake it up(supposedly)
Definitions:
Create Timers:
Handlers:
Main() function...
I am working with the nRF5340 DK.
I am looking to sample an ADC pin to sample at a sampling frequency of at least 1kHz and I would like to use DMA to write the data directly...
Hi everyone, I implement nrf5_SDK_17.0.2 ble_app_uart example, but when I connect both GND wire and TX wire of the external device to my nRF52840 DK first, my nRF52840 DK...
Hi
As mentioned in this question: https://devzone.nordicsemi.com/f/nordic-q-a/69533/set-tx-power-on-zephyr-device , there is a sample to change the tx power using some HCI...
Hello,
I am trying to use the ble_app_rscs example app into the nRF5_SDK_17.1.0 package for connecting the nRF52840-DK board to the nRFToolbox Android application. However...
I have a small program that is to be used in production to test my device. It has to be scriptable so I'm using teraterm over rtt.
No external IO for a serial port.
Everything...
Hi Nordic,
Can you tell me how to remove commissioned a node from open-Thread ? Basically I want to remove a node from one network and put it in some other network. Are...
Hello,
I encountered a problem while trying to flash my PCA10040 nrf52 development kit.
I am able to compile my code in Segger Embedded Studio without a problem. The chip...
Hello:
I am using an nrf52840 on a custom board with W25Q01NV NOR Flash with the Nordic QSPI-NOR driver. Programming is with NCS v 1.8.0 (upgraded yesterday) and the VS...
Hi Team,
I am developing an application that required SPI communication with msp430.
But, some received characters are disorders, I see them by JLinkRTTViewer logs. For...
Hi
I'm using nRF51822 xxAA (256 Kbyte ROM). My code size are 66 690 byte, I'm using IAR.
Application memory setup:
This means that I have 131 KByte code size for my...
