Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
We are implementing on nRF52840 with latest NCS version the following code:
The nvs_init() function is halting due to an error at flash_sync_mpsl.c within nrf_flash_sync_exe...
Hello,
We are working on the nrf52840 custom board in that We trying to update firmware via DFU.
Problem definition : First we update firmware via DFU application boot...
Hi ,
We have a custom hardware with an Active GPS Antenna (that is connected to the main board with u.fl connector).
I ran the GPS SNR command to test the performance...
I'm designing a PCB that uses the nrf52832 with an external RTC, the DS1339 ( https://datasheets.maximintegrated.com/en/ds/DS1339-DS1339U.pdf ). I want to use a single 3.3V...
I'm enabling external power off warnings, as specified in section 5.22 of the AT command guide.
When I drop the supply voltage I see a LTE network disconnected message from...
Hello Nordic!
I have been developing a Zigbee application and now, I need to connect via Serial communication with another device. I just need to listen to the port, not...
I am using flash_fstorage_s140_pca10056 example from SDK v17.0.2 , I see that the start address is 0x0003 E000 and the end address is 0x0003 EFFF respectively.
I want to...
Hi,
I am trying to check how DFU works but I have problems setting it up. I will describe all the steps that I have been doing here, so that it will be easier to try to...
Hi, I am designing a custom board usign the NRF52832. Im using this externar crystal https://es.rs-online.com/web/p/unidades-de-cristal/1753468/ . but I have seen that many...
Hello Nordic Support Team
I need desperate help to get my proof of concept working. I have been able to prove that the applicational concepts work on the nRF52840 and now...
I'm trying to create an application on the nRF52840 that can read serial input from an external GPS chip and also provide log output via USB. As I understand it, the UART...
I want to read access address of a connection between master and slave in master.
I need access address and not the MAC address after connection establishment.
Is there...
Hello, when developing our application, we run into a problem. We are running Zephyr 2.4.0 on nRF52840 MCU. We use LSM303AGR sensor, which is supported by zephyr LIS2DH driver...
Hi,All:
1. As the topic, now i just make bootloader,How do i perform a app entrance? and how to staging, combing.........in the picture as below. Or,on the other hand,how...
Dear,
I am trying to manually toggle GPIO0_2 by writing into the GPIO register, 0x50842504[bit 2]. The output of GPIO0_2 was always static in either high or low.
If...
