How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hello, I get the
"ERROR: The --family option given with the command (or the default from nrfjprog. ini)
ERROR: does not match the device connected."
message after...
Good morning,
this is Algocraft (www.algocraft.com), an high tech company whose core business is to develop, design and market a wide range of professional systems dedicated...
Hi,
We designed the circuit followed the reference circuit(QFN48), but we always failed in the 8kv ESD test.The CPU always reset while ESD testing.
The 8kv ESD power...
Does anybody got an app inventor2 "project" to communicate with the (Adafruit) Bluefruit LE UART (or SPI) ?
Note: my Android version is 4.4.2 (LE "advertising" not supported...
Hi,
We got a few boards that have large ADC error. I've already using nrfx_saadc_calibrate_offset to calibrate the offset so I suspect it's caused by gain error. The error...
Hello All,
SDK -- 15.3.0
I want to interface MX25r6435f with NRF52810 so i saw some older queries regarding this Flash driver,
so some where i saw that in sdk QSPI example...
Hi!
We are working with the nrf5340 (custom board-revision QKAAAB) and we are facing an issue when resetting the application. If we add some functionalities to a bluetooth...
hello,
i am using nrf52832 with sdk 15.2 and i want to advertise my beacon like the above picture how can i change the length type and values i can understand the app beacon...
Once paired & Bonding is completed. If neither side pairing & Bonding information is deleted. After restart the device is not advertising again. We are getting PM_EVT_CONN_SEC_FAILED...
Hi, Good afternoon. Some Questions.
1.
Is the Enhanced ShockBurst (ESB) protocol applicable to the nRF5340? I'd appreciate it if you could give me details on how to get...
The nrf52833_peripherals.h file has the P1_PIN_NUM set to 10 but the pca10100.h file has ARDUINO 8-13 pins mapped to port 1, pin 17 to 23. This cannot be correct and causes...
Hey all,
I want to try the Asset Tracker v2 (NCS v1.6.0) Application in AWS, so I followed this guide .
When I try to create the CA certificates and register them in AWS...
Hi,
I'm trying to build the smp_svr example for Thingy:52 but build fails when linking.
I can build for the nrf52dk_nrf52832 which uses the same chip. What can i do to...
Dear Nordic Team,
We have a running product that is using 32KHZ quartz from MicroCrystal : https://www.microcrystal.com/fileadmin/Media/Products/32kHz/Datasheet/CM7V-T1A...
Hello,
I have a design where I am using an nRF52840 along with a SKY66112-11 and am using Zephyr/MPSL for both BLE and Thread. I also have a run-time radio test mode which...
Hi, I have installed the most recent version of nRF toolchain manager for windows (V0.9.2). nRF SDK V1.6.0 was released a couple of days ago but it is (not yet?) in the list...
I am new to BLE.
My question is similar to the one below.
https://devzone.nordicsemi.com/f/nordic-q-a/22596/nrf51822-central-connect-and-communicate-with-2-peripherals...
