Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
Hi,
I just got Thingy:91, and I was trying to see the response for a simple hello_world (found in zephyr\samples) application from Thingy:91.
Thingy:91 got programmed...
Hi,
Are LTE-M efficiency/TRP/TIS results of the nRF9160 DK on-board antenna available? In case there are several DK revisions available, does the version affect antenna...
Hi,
I am trying to understand how to enable SPI in blinky application provided by Nordic. My intention is to transfer data between the two Nordic development kit running...
I have advertising in s130 set to BLE_GAP_ADV_TIMEOUT_GENERAL_UNLIMITED. The idea is to advertise until a connection event is received. In reality the user will pull the finger...
Hi ,
1. I learned from Nordic FAE that on the nrf9160 module, 10 minutes after the edrx mode, the nrf9160 module automatically powers off the sim card to save power,
2...
Hello Team,
I want to use scheduler to schedule two tasks i.e task_1 and task_2. The task_1 and task_2 are as follow:
void task_1() { printf("Task 1 ran"); }
void task_2...
Sorry this might be a stupid question.
We are evaluating some modem to develop a IoT device, NRF9160 comes up to our list as its tiny size.
In the design of IoT device...
I wants to use break point in project but when i set break point then 4 or 5 times working after that goes to NRF_BREAKPOINT_COND, I am using nRF52832. so guide me where is...
We are using NRF52840 and we have a watchdog timer connected to reset the Nordic, if needed. What is the minimum and maximum time need to insert a reset on Nordic?
thanks...
I want to transfer sensor data to a raspberry pi using the in-built USB on nrf52840. The example codes have the following classes: CDC_ACM, Audio, HID and Mass storage. I...
Hello,
I am just curious wether there are any specific recommendations or requirements for the package-sizes of capacitors/inductors listed in the BOMs of the nRF52840-reference...
Hello,
I am working with the latest version of nRF52 SDK 13.0.0, when I was implementing my own bootloader application, I tried to start an app timer in my code to invert...
Hi there,
Could you please tell me the exact part number of nRF9160 and nRF52840 on Thingy: 91?
I cannot find the specific information even though I looked through the...
Hi All,
How many nodes can connect to a node in ble mesh network. I go through code in ble mesh, but i did't found the answer.
Can any one please tell me.
Regards
...
