Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
I think I am having a problem with Radio Notification. I am not sure. I have an application where I need simultaneous “Central and Peripheral”. Device only needs to advertise...
I am trying to do Mesh DFU.
I have done updating ble_app_blinky successfully for the 1st time over mesh but after that, I tried to do again by increasing the application...
Hello,
I am working on a custom board using a nRF52840 based module. I am using SDK 14.2
I am running the following simple code to sense when an GPIO goes to a low state...
I know I can set the TRACEMUX pins to 0 to enable the GPIO instead of SDO. I do this on the first line of the program.
My problem is that when I click debug, from the time...
hi The serial ports p0.04 and p0.05 on our hardware circuit. We can't communicate with the board with nRFgo studio after modification. The serial port has been closed. Request...
Hello everyone,
In the past few days I have been struggling with the following issue: I have a file on my iPhone, I want to send it to the NRF52840 using BLE (the softdevice...
Hi,
I am running the following setup, both on nRF52840-DK:
1. Central : Always scans , when he finds devices with NUS service -> Initiate a connection
2. Peripheral...
My company has a situation where we have 3+ devices.
A is the provisioner (also an embedded device)
B is a already provisioned device
C is a non-provisioned device...
Hi,
I have made a custom board with u-blox bmd-340-A-R-01 module and trying to erase the flash with PCA10040 DK. I am getting error when I try: nrfjprof -e. Please find...
Serial Example in Mesh SDK allowed embedded system to provision a Mesh network
by interactive_pyaci.py controlling nRF52 with serial example with UART.
But the example...
Hi Nordic
SDK15.2 based application and bootloader running on NRF52840 based UBlox module.
We have the following symptoms happening in the field:
- 2 channels of the...
The customer wants to implement a hid function like the nrf52840 on the nrr9160, and there are no off-the-shelf routines or references to add the hid function.
Hi everyone,
I need your advice regarding the regulator configuration of nRF52840
I am designing my own PCB using Raytac's module MDBT50Q-1MV2 that carries on the nRF52840...
Is this the right cable to program the Thingy 91 using nRF9160-DK?
https://www.digikey.com/products/en/cable-assemblies/rectangular-cable-assemblies/450?k=adafruit%201675...
Hi,
I've developed a custom board with nRF5340-QKAA (see schematic sheet attached). nRF5340's VDD pins are not tied to VDDH pin, then I assume the nRF5340 automatically...
