Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
HI,
I want to use nrf52833 for receiving SAADC DATA in my phone by using BLE_NUS_DATA_SEND.
Here are my codes.
In 716 ~ 724 lines, I added codes about BLE_NUS_DATA_SEND...
Hello
I'm using the nrf52840 DK with sdk version of 15.0.0.
My requirement is to flash my project through cli commands, so I have followed the following steps in below...
Hi,
I recently updated my toolchain using the nRFConnect tool chain manager.
(I was seeing problems after an OS update)
This update fixed my problem but when I build...
Hi,
Please, what are the settings for gpio driver in sdk15.2. for some gpio pin to be able to sink current (to act as gnd? ). In my project it is used for loadswitch enable...
Hi,
I have bumped into this bug in SDK v17.0.0 and SDK v17.0.2 but no fix yet.
We are using nRF52840 with S140.
Can you please make sure to release this fix asap because...
Hi There - My question is about the nrf5340 dual core cpu. I’d like to know if it is possible to have one core polling sensors on the spi bus - then pass this data to the...
Hello
I am testing sending the value to the app through the ble_app_uart of SDK v17.
I know roughly that I need to use 'ble_nus_data_send', but it is not printed from...
I add this code in 'static void on_connect(ble_nus_t * p_nus, ble_evt_t const * p_ble_evt) ' on the sever. But I still got an err_code NRF_ERROR_INVALID_DATA. Softdevice is...
Hello,
I want to compile the "pca10040" template after installing the SDK and the command line tools with Segger Embedded Studio, but I got the error:
cannot find ......
Hi,
Currently our team would like to start using Zephyr for our development, but some colleagues fear that it will use too many resources. They saw that our first test project...
Hello.
I'm using Zigbee SDK 4.1.0 with nrf52840.
When the firmware is configured as Zigbee router, it forwards route request data packets with incorrect contents.
...
Hi,
When I try to compile the gps nrf9160 sample with the SUPL enable, the compilation crash each time.
I get the error "Assertion failed: CONFIG_FP_SOFTABI is not supported...
I want to implement BLE using nRF52840. Without using SDK, we have formed a new project and successfully controlled GPIO control and UART. She wants to use the Softdevices...
I see the NRF8001 doesn't necessarily require the 32.768 Khz oscillator to function. My understanding is it's useful to preserve power. If I'm not worried about power draw...
