Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
Hi everyone. I'm trying to add UART Service to Mesh light switch example in Mesh SDK latest version 1.0.1. Is it possible? And When Nordic will provide integrated Mesh SDK...
Hello everyone,
I am currently working on a project, where I want to interface UART to a Bluetooth mesh network. The project is very similar to the light switch demo, because...
Hi Team,
I am working on Mesh SDK 3.10, I have requirement of mesh with Ble Uart. So I decide to take this example "ble_app_uart_coesixt". I build this example without...
Good day, support!
I have a couple of questions regarding the firmware of the nRF52840 dongle.
1) How to identify the firmware version that is nRF Connect flashing ...
After following the " Using a custom Secure Partition Manager with your application " Guide for the nRF5340-PDK, I experienced following error:
I tried to create a Non-Secure...
Hello every one.
I am new with Segger and nRF52.
I tried to create my own library for OB1203 sensor.
But i stack here when Segger view this error: Below is my screen...
As we are performing climate tests for custom PCB based on Nordic nrf52832 SOC, in low temperature i.e -20 Deg C the communication is not stable. After verifying the HFCLKSTAT...
Hi,
We thought to have a setup like this
1<-->2<-->3
1 is MESH ADV device with some mesh model
2 is MESH ADV + regular BLE stack support
3 is Gateway with...
I am trying to collect sensor data and store in flash using qspi interface. Unlike the peripheral example code, the qspi data handler function is not getting hit with ble...
Hello, I have another problem... i work on nrf9160 dk
I try to send http post when i pressed button 2 but this doesn't work.. Below you could see my code who block on printk...
I have been reviewing this merge: https://github.com/NordicPlayground/fw-nrfconnect-nrf/pull/1982 and it appears that there is capability in the fota example to enable https...
How to configure the start address and size of flash memory and nrf52832 in SES and how to calculate the size? How to calculate the start address and size of app and bootloader...
Hi,
Current Status:
I'm trying to run the fpu_fft example from the SDK 15.3.0 on my nRF52832 DevKit. When I clean and build the project in SES everything is fine and I...
Hi, I have a question about unknown flash data from MBR area which start from offset 0x0000035C, 20 bytes data show as below.
Data[20] : FF FF FF FF FF FF FF FF FF FF FF...
