Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
I would like to use the nRF24L01+ for a telemetry project that requires broadcast at 100% duty cycle at a fixed bitrate. Ideally, we could also use our own frame format. ...
I am trying to use whitelisting and a passkey to add security for my application. So far I have the passkey set up so that it is working on the master control panel on PC...
Dear sir.
From [nRF51_Series_Reference_manual], ADC maximum input voltage has two rules.
The ADC should not be exposed to higher voltage than 2.4 V on an AIN pin...
hi
i have one custom service that have 6 characteristics
when in android i want to write in one of characteristics it take about one sec .
is this for having 6 characteristic...
In the Androir master control panel app, in the scanner results there is a 'Type:' line for each device. Most of them around me say 'UNKNOWN' however some say 'BLE only'....
SDK 11.0.0, S132 v2.0.0, nRF52.
I have searched through the many questions already on the dev zone on this topic, but cannot solve my problem. I tried adding the dfu service...
hello all,
i am a begineer to nordic . i am trying to read adc PCF8591 value through TWI and i want to print the value in UART TERMINAL.
i have written the code. but...
Hi,
Im trying to connect ble_app_uart to my gsm module. For some reason program fails at runtime. I was expecting to find a filename and line number where the error has...
Hi,
nRF52 Board, S132. Now, I want 6 pwm, 6 adc .
nRF52 has 5Timers, Timer0-Timer4.
Now, I allocation these timers as follows:
//TIMER0 is used by softDevice
APP_PWM_INSTANCE...
Hi,
I want to access restricted peripheral: TIMER0.
After small research found that I should use sd_ wrappers, in my case sd_nvic_SetPendingIRQ(TIMER0_IRQn) however I...
Greetings,
I'm working with LPCOMP to detect a signal. This signal is the output of an opamp amplifier. What is happening is that when the LPCOMP is switched on there are...
Hi,
I am using SHT21 Temp sensor via TWI manager. As per the spec shown in the image
I have to add 20us delay between the sensor ACK and STOP command.
Is there any...
Hello, I have the Beacon Development board and the sample firmware downloaded and up and running in the Keil MDK IDE. My specific application requires some code to execute...
Hi,
i want to add a current time service to nRFgo. In particular for the glucose measurement profile.
Any suggestions for this???
I add manually the current timer service...
Custom nRF51822
SD130
SDK V11
So sometimes my disconnects seem to fail, the return code says success, but when I try to reconnect I get an error 18, NRF_ERROR_CONN_COUNT...
