I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hi,
I would like to store firmware version number at a particular offset from the application start address so that it can be retrieved by boot loader as explained here...
The comment in dfu_init_prevalidate says the following
// To support application versioning, this check should be updated.
// This template allows for any application...
Hi,
As far as I know the ADC pins can be used as digital inputs. Is it the same with NRF9E5? I could not find anything like pros/cons. Datasheet doesnot say anything about...
Hi,
i have been struggling with UICR Config in nrf52. The code:
NRF_NVMC->CONFIG = (NVMC_CONFIG_WEN_Ren << NVMC_CONFIG_WEN_Pos);
while (NRF_NVMC->READY == NVMC_READY_READY_Busy...
Dear nordic.
We are developing nRF51822 with S120 as central.
When advertising from Peripheral, RSSI value is changed it's position.
Measured RSSI range is -60 dBM...
Hi,
I am trying to get the sniffer to work on my new Win10 machine.
I am using the PCA10001 board.
I have tried:
SEGGER: 6.00g and 5.12f
Wireshark: 1.12.x,...
Hi to everybody,
I have configured the nrf52 DK (SDK 11) with FreeRTOS and the UARTE with a DMA buffer of 16 bytes and it works. The problem comes when I don’t want to...
Hi,
I'm working on ble_app_hrs_c application with Nordic beacon.
Using nRF51822 Ver.H0 with S120 and modified to using Internal 32.768KHz RCOSC and UART at 115200bps...
Hi guys,
I'm playing with a beacon kit, nRF51822-BK.
It works out of box, no problem but I have a simple question. One of our customer asked me if is possible to control...
Hello,
I am using nrf51 SDK version 10.0.0 along with the nRF51822, and I believe I have found an issue with a macro that is supposed to check the correctness of a bit...
Hi All,
Another question for those out there much smarter than myself...
We're developing an application using nrf52, sdk11 and softdevice s132 2.0.0 and have been using...
I see it is advised not to just stop a timer, but to also shut it down for certain of the nRF52s. What call is necessary to achieve this since I understand it is deprecated...
I want to read the onboard (dev board) buttons which i believe are P13-P16. I want to know the working code.
uint32_t app_button_is_pushed ( uint8_t button_id,
bool *...
I am trying to estimate the memory usage of the s132 v3.0.0 running on a nRF52832. I am interested on acting only as a peripheral with one link at a time only. From app_ram_base...
Implementing my own protocol stack with low-level programming of the radio, can I broadcast by simply programming all units to receive the same address?
No addresses (such...
