why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Do you a way to get better range for BLE.
Distance outdoor Number of samples per second using the development kit. ( 12 bytes)
15m 100 samples
40m 60 samples
50m 50 samples...
Reading the s110_nrf51822_7_0_0.migration document there's a small section which states that due to an issue in the release you need to do the following ..
sd_ble_gap_enable...
I'm learning about GPIOTE and PPI and looking at an example I come to the following code but now it act incorrectly. So as you can see I'm enabling the interrupt for GPIOTE...
I am working with the nRF51 Software Development kit for the nRF51822 Evaluation kit
There are some kind of type qualifiers such as __I, __IO appearing in the header, e.g...
I am following nRF51822_Evaluation_Kit User_Guide v1.2.pdf (page #9) to run Heart Rate sample but I am unable to get an expected result (LED 0 should be lit) when I am pressing...
Once I downloaded Soft Device 110 (s110_nrf51822_6.0.0_softdevice.hex) into my Evaluation Board's chip I ran nRFgo Studio and saw that the size of the Region 0 is 80KB and...
My Board PCA10024 (nRF51822 Chip QFAAG0) consumed at least 18mA with external 3V battery.
The nRF51822 chip itself consumed only 5uA in sleep mode.
What's go wrong? So a...
Hi,
in, for example, the multilink example app, central role.
I would like to disconnect a peripheral role device once a notification has been received...
... is it correct...
I am using a stripped version of ble_app_hrs of SDK5.1 with Softdevice 6.
I stripped all services from ble_app_hrs except the DIS. ( so removed battery, hrs, buttons and...
Hi,
question is probably trivial, but I cannot find answer for second hour, so maybe somebody know, how to set that same address for Application downloaded from Keil and...
Is the nRF51822 susceptible to being bricked if the programming port is accidentally disconnected during programming? Does it use any protective measures such as a checksum...
I'm using nRF51422-QFAA E00 with S310, nRF51 5.2.0
When I configure ANT channel as a Master with Network number 0, all works OK. But if I try to set different network number...
50ms_measure_30ms_other.jpg
Attached is current measured using the s310 softdevice
Every 50ms timer takes a twi measurement, which is a twi 6 byte read followed immediately...
I am trying to write a bootloader that will work with the S120. Both the examples seem to only work with the S110, so they don't help much. I already have the binary I want...
Hi,
we can send data from server to client by sd_ble_gatts_hvx() in ble_app_hrs but:
1.How does the client receive those data?
2.How dose the client send data to...
