S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
I think the figure 10 in nRF9160_PS_v2.0.pdf chapter 5.1.3.1 is worng.
R and C should be swapped.
It is different to Figure 118 chapter 10.3.1 R2, C10.
Exist a list...
Hello,
I have the following problem. I am using the SDK for Mesh 4.2.0 with the nRF5 SDK 16.0.0 on the nRF52840 DK, I am using the sensor model and I have extended it with...
Hi,
I want to make a BLE Multirole application where the central demands LESC, bonding and MITM and peripheral connections is JUST WORKS bonding.
Is that possible? If...
I'm trying to modify the flash_fds example to write a start time when a button is pressed, then an end time when the button is released. I get the time over TWI from an RTC...
Hi, We are into Commercial health devices using nrf5340 and looking to use AoD technology for our device to get its indoor location. We need to have a Receiver with antenna...
What are different options to load the soft device on custom board? Currently, I am using nRFGoStudio to load the softdevice on nRF52840 DK. We will not have segger hardware...
My app uses a proprietary service and characteristic UUIDs; the app needs to completely manage all characteristic reads and writes. With nRF Connect, I can see my service...
Hi Community,
For community's help I success to create 12.3.0 DFU version get work.
So now I try to make all hex(softdevice, bootloader, application) to one hex file...
Dear Nordic,
We are trying to figure out the difference between the working/feature set of nRF_crypto file and mbedtls.
Which one is better and why?
Ambimat
Hello,
I wanted to ask which uart library we have to use in SDK16 and which configuration to have a LOW POWER UART
We are in development phase on the devkit PCA10040 and...
Hi guys,
So i have some Nordic DK board including some dongles, NRF52840 DK, NRF52833 DK running with Zigbee and thread SKD 4.1.0 and make a mesh out of them. But I have...
Hi,
I have to control 16 pin output pins based on the 16 pin interrupt.
Is it possible to have 16 pins interrupt in nrf52840 . Pin change interrupt
when i config
...
I use SDK 15.3, nrf52840.
https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/setting-up-the-timeslot-api
Normal use most of the...
We are developing a new product that requires extremely low power consumption with a target to run advertising intervals of between 2 to 10 seconds.
We are using the nRF52805...
Hello everybody, My nRF9160 simply does not connect, I already followed all the instructions that come in the quick guide, I successfully registered the SIM card in the nRF...
