Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
How does the interrupt latency compare between COMP/LPCOMP and GPIOTE? Are t LPCANADET and t PROPDLY the correct field to be looking at in the specification? The electrical...
Hi Nordic Team,
My Board: nRF5340 DK; SDK: nRF Connect SDK v1.5.0
I am new to BLE developement. I am trying to design a GATT service which can be accessed by nRF Connect...
I'm trying to use UART flow control and assign RTS CTS pin numbers.
What's the corresponding number for P0.02, P1.15 each?
And where can I find this information?
Hi,
I have used nRF52811 SoC in my custom design. In this circuit i have used SWD interface only as per reference design. I have used same SWD 10 pin connections as mentioned...
128 MHz or 64 MHz operation is mentioned in the specification (page ii). However, can MCU be capped at around 12MHz? How about the current consumption?
I am starting an experimentation effort with Nordic Mesh SDK. I am using Segger Embedded Studio.
I can open/compile/download the Mesh SDK examples.
I wish to start to...
Hi,
Hope someone can help with the following Q:
We are planning to make an new battery based iot sensor design based on NRF9160 SIP mounted on our own pcb with several...
Hi
I am working on testing the PSM on my nrf9160 custom board using SLM
After powering up and setting AT+CFUN=1, when I send the following AT commands:
It seems the...
I was attempting to implement the secure bootloader example on my custom board (nrf52832) and it failed, so I have been trying to reprogram the board with our normal application...
Good afternoon,
I've created public and private certificates for connecting with an azure hub using a nrf9160dk. I succeeded but, later, i was investigating a bit deeper...
nRF5 SDK can enable radio notifications by few API calls for example: https://devzone.nordicsemi.com/f/nordic-q-a/3481/radio-notification-only-after-ble-radio
with NCS,...
Hi,
I use the example Android Application from Bluetooth to send a generic onoff message from the phone to the proxy node which is also a light switch client ( https://www...
Hi,
My app, based on SDK17.0.2 and SD S340 ues both ANT+ and BLE. While connected to the app runing on the NRF52 from my phone app through BLE, my app on NRF52 sometimes...
Hi Team,
We are designing the Nb-IoT Pet Tracker with nRF9160 SOC and We are performing the NB-IoT Body SAR Compliance Testing, For that, we are trying to communicate...
Thanks in advanced. Platform is: nrf52832-qfaa, SDK_17.0.2. I use microusb interface as multiple port for charging and uart I/O. I always get APP_UART_COMMUNICATION_ERROR...
