Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
When I generate bootloader settings using nrfutil 6.1.0:
The output indicates the start address is 0x3fc00:
However, looking at the hex file, it contains identical...
I'm measuring the current of the following code:
I'm not using softdevices.
I have nothing more connected to the board than the power.
I measure about 0.320 uA which...
I'm trying to make a test app that includes sample code from GPS and udp examples.
Building for nRF9160DK with west.
Here's my Kconfig:
```
# # Copyright (c) 2020...
Please help me to eliminate the error : "cannot open source input file "nrf_erratas.h": No such file or directory" for nrf51422 for nrf 51(12.3) sdk in keil version 5
Hello, We noticed that when we enable the whitelist, we can successfully filter out connection requests, but not scan requests. Our device still responds to every scan request...
Hello sir / ma'am
I want to implement OTA with zephyr using openthread but the size of my code .bin file is too much like 412kB .
How can I reduce my code size ?
What...
Hello
I am building a code with Openthread (NCS V1.4.0) and the size of that generated Bin file is 405kB. I would like to know why size of that file is more? I need to reduced...
Hi!
We are working with the nrf5340 on a custom board and we are trying to reduce its power consumption to the minimum possible. We have a beacon advertisement application...
Hi all,
I have just some issues with sd_flash_write and sd_flash_page_erase functions. I have created some code to read the temperature value and save this value in memory...
Hi,
I am considering nRF52 (most likely nRF52833 or 811 ) for a new design - curious how mature is the concurrent multiprotocol support in nRF52 - in particular for nRF52833...
Hi All,
We are using nRF52840 MCU and SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71. We are designing a device that uses switches connected to the below pins,
Pin...
Hi,
I use a custom board, softdevice and boot loader.
I use DFU to update a slave chip firmware. Everything goes right until we invalidate and write flash :
// Invalidate...
Hi
i use sdk 17.02
custom board
soft device
when i program input digital pin I have an extra consumption of arounf 9µA versus not using it.
Could you tell me if...
Hello,
I am using FDS successfully with SDK 17.0.2, secure bootloader and softdevice. Bluetooth (BLE) environment, if it does matter.
I can read and write data. But following...
hi guys
i develop mobile app for iOS and use nrfMesh lib v3.0-beta1. i have few nodes subscribed to a group. I send GenericLevelSet message to a group and receive successful...
