Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hi,
I am trying to implement capacitive touch with nrf52832.In our application we require three events to be generated.
1)On holding for 3sec(Device Turn ON)
2)On holding...
Hello Nordic Pros,
I haven't been able to chase this one down on my own, so any help is greatly appreciated...
We are developing a product and app that connect to either...
Hello,
I'm using the rigado BMD350 in a new device with the legacy BMDware (AE firmware).
I'm have enabled the uart service and i'm debugging the transmission using the...
Hello,
I am trying to use the CLI example, but when I compile and upload it, LED1 does not blink and I do not get anything back on the serial port.
There is no error during...
Hi,
According to the data sheet, nrf52840 supports XIP mode on QSPI flash. Can we configure I2S(easyDMA) to load the tone from external flash with XIP address and play it...
I use a motion sensor interrupt and 4 buttons and one charge interrupt, all works well in product development, but after go into mass production, some pcs product( 1 or 2...
On the previous nRF51822 project the SWDIO pin could be used for nRESET.
The nRF52832 Product Specification and example code program nRESET to P0.21.
The Product Spec...
Hi,
One of my customers examine the feasibility of using nRF52832 as Peripheral only ,his mandatory request is Security because the product is an electronic lock.
Please...
I use nrf51822 to do bluetooth keyboard, I hope the function is: I want to change the IRK value of the bluetooth keyboard each time it is paired and bound,Anybody know how...
Hi can somebody help why nrf52840 doesnt be reseted when you press SW5(if boot/reset)? I have alredy with tried with few examples flashed on nrf52840 and in Segger IDE set...
Problem :
I have two I2C devices and would like to connect them both to nRF52840 DK on different I2C pins. According to datasheet nRF52840 has two I2C pins (P1.00, P0.22...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hi,
I am trying to build out a button pressing scheme for BSP on a custom device with 15 buttons operating on a BL652 Laird Module (underlying nRF52832). After modifying...
I'm working with the NRF9160 DK and have found the sample times for the ADC to be abnormally long. I am sampling three channels and seeing a total time for the ADC read of...
Hey guys, I am using 2 nRF52832 boards with a PCA10040. I program my boards with the BLE UART central and peripheral examples. I was wondering if it is possible to, and if...
