Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
In this application, I tried to enter a wrong bonding passkey to test PM_EVT_CONN_SEC_FAILED case. But I found that the program went into this case and after executed "sd_ble_gap_disconnect...
We developed a new BLE hardware product using the Laird BL652 third party module. Our product is based on the latest Softdevice S132 V5.0.0.
Now I'm starting the Bluetooth...
I have problems getting the beacon example in the new mesh SDK v0.10.0 working.
I invoke cmake with this command:
cmake -DTOOLCHAIN=gccarmemb -DPLATFORM=nrf51422_xxAC...
Hi there~. This is Matthew! I saw a thread explaining that the production variants of the nRF52840 will first be available Q4 2017 at this link .
I was planning for BLE...
Hi,
I had a difficult problem.
First, S110 & SDK9
ble_stack_init () is the source.
static void ble_stack_init(void)
{
uint32_t err_code;
// Initialize the...
Hi. I'm using nRF51822 as Peripheral.
To init the service for example "NUS", i have to call NUS_BASE_UUID as below..
#define NUS_BASE_UUID {{0x9E, 0xCA, 0xDC, 0x24, 0x0E...
Hey guys,
From what I understand, the minimum connection interval on say, an iPhone, is 20ms. Also, you can send up to 6 packets of 20 bytes within a connection interval...
I have established a ble connection between two dk boards, the code I based on is the ble_app_uart_c and ble_app_uart, and try to detect some rising edge delivered from the...
It's kind of relative question with my previous question.
"When smartphone range is shorter than a peripheral(nRF5X), is there any way to receive an advertisement from the...
Hi all, I tested the example: Experimental: LE Secure Connections Multirole Example with my smartphone and it is working fine, but when I tried use LESC on my peripheral device...
I can't open a com port after starting the nRF Connect app. This happens in Windows (native) and also a Linux virtual host with the com port passed through. I'm using a nRF51...
I found strange behavior when using back-to-back packet transmission.
Configuration of PTX/PRX is:
No Auto-ACK (disabled)
CRC 2 bytes
Packet length 13 bytes
Addr...
I have the blinky examples working, but have not been able to get any example code using any gpio input to work. they compile fine but the buttons done seem to work. I'm using...
Hello,
I'm using the sample project from this post .
Following the steps and using nRF52DK, one for server and one for client. I've modified the server count from 3...
