dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
I add the NUS in the ble_app_hids_mouse example which the sdk version is 14.0.
There are four services in the project: dis, bas, hids and nus.
When I connceted the...
hi all ,
I am looking out theory about SM layer in BLE . I read CoreV5.0 but I do not understand much about pairing , bonding , STK , LTK . Can you give me some document...
Can the link between two devices communicating with each other via NRF24L01+ be improved by using Tx messages with no ack (W_TX_PAYLOAD_NO_ACK) instead of messages with ack...
Specifically, sinking a Cree C503B green LED (Vf 3.2V at 20ma) from a GPIO configured for high drive, without a current limiting resistor, from VDD 3.6V?
Figure 23 “GPIO...
Hello All
We are using nordic thread sdk's sample simple coap client and server.We want to ON/OFF LED of coap client from coap server.
Can any one help how we can achieve...
In SDK13, the initialisation of the low frequency clock used to be done within sd_softdevice_enable . In the SDK14 version of nrf_dfu.c , the LF-clock is already initialized...
Hi, I want to use the AES-CCM of nRF52832. But it can not work with the softdivice. I have read the following question and answer.
https://devzone.nordicsemi.com/question...
Hello All,
I have a peripheral device where one service with 4 characteristics is implemented.
Out of these 4 in 3 services notify is enabled.
Now I want to subscribe...
I have a situation in which a central device (A) must be able to receive from a power constrained peripheral (B) with very low latency, but likely at long intervals.
To...
Dear Nordic,
I tried to download the new SDK nRF5-SDK-for-Thread from here:
www.nordicsemi.com/.../60504
However, when I clicked on it I only got the TTM 0.11.0.
...
Hi every one ,
I am using NRF51822. I download the code
from this link. github.com/.../nrf51-ble-tutorial-advertising
I able to flash the hex file & see board are...
hi~
i am working with nrf 51822 with custom board and softdevice s110.
i am using is7020-a20 temperature / humidity sensor via twi (i2c)
i tried 2 versions of twi example...
I followed this guide , I'v managed to run make files and flash them using the terminal, then when trying to build the project in Eclipse, I get this :
Make: no rule...
Hi,
I am following the "Bluetooth low energy Services, a beginner's tutorial", however, this tutorial is written for SDK V11.0.0 and I am using SDK14.1.0, softdevice 5...
