Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello everyone.
I am developing with nRF 52832.
However, when I call UART_init() function. my source code outputs an error message.
source code is under the line...
Hello, i'm using a nRF52840 on a PCA10056 and want to wake up from __WFE() with a minimum delay. When i'm using the debugger, i achieve a low latency but without the debugger...
Hello All,
We are working with one of the customer, where he is asking for range 200 meters between 2 nrf52Dk(nrf52832) and he want us to prove the same using two development...
I am trying to use the cryptocell in the bootloader (bootloader_secure_ble) for verifying dfu packages, but fails in signature verification for the same dfu package, same...
Hello,
I am designing the NRF52832 based board.Specifications of capacitor in reference design is as follows:
0.8pF, NPO, 5% tolerance
But with my vendor these two capacitors...
I am designing nrf52832 based board. In matching, 3.9 nH inductor is given.
I have selected the componenet with following specifications :
Specifications of inductor...
Hi Everyone
I am using nrf52832 development kit , sdk 14.0.0 with iar and i am trying to merge the ble_app_buttonless_dfu and ble_app_uart code.
I have done the changes...
Hello guys.
I am able to save an array to flash memory unfortunately I can not save a struct in flash. I am referring to this question Save struct to flash . However I...
Hi,
I'm a beginner in programming Nordic uC and I would like to know how to enable the watchdog in my application. Are there particular functions to call?
Thanks!
Hi,
We have a prototype application which requires an NRF52 based peripheral to be inside a metal cabinet and to connect via BLE to a central while maximising the link...
When calling access_model_application_bind() , NRF_ERROR_NOT_FOUND is returned?
I have had this working before, but after adding another server model I am getting the error...
Hi,
I am implementing modified DFU for nRF52832 which uses external flash memory. If power loss occures during update process, device then start update process from the...
Hello sir,
I am working on my final PCB design using nRF52832 chip. As per your reference Bill of material i use same part number for all components recommended by you. But...
I have a custom board with the nRF51822 QFAA . Schematic:
In order to compile the firmware, I'm using MinGW . As you can see, I'm also using the SDK 12.3.0 .
Finally...
Hi,
I am using nRF52832 and softdevice is S132 adk13.1. My application is read 3 ADC channel one by one and send this value to android app using NUS. For this i have use...
