Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hi,
I am trying to compile some RuuviTag application using nRF5_SDK_12.3.0_d7731ad
2 symbols are not defined,
APP_CONFIG_ADV_FRAME_SPACING_MS_MIN and
_ADV_FRAME_ETLM_SPACING_MS...
Hi nordic guys,
After the hid device delete the bond info but the PC did not remove it form the bond list,and i want the hid device to reconnect the PC quickly again but...
Hi,
in nrf connect app i see it is possible to update bootloader over ota.
How do i generate ota file properly? I tried generating zip and hex but the app says "no matching...
I have nRF6310, nRF2727.
I wonder if I can update the nRF24L01 firmware with the above board.
I wonder if there are any additional devices or other methods...
I am using ble_app_uart in one nRF52 EVK board(peripheral) and ble_app_uart_c in another nRF52 EVK(central) and sending data of Device under test through UART. When the data...
Hi,I want to use RTT in bootloader project.
First,i add all files(SEGGER_RTT.c ,SEGGER_RTT_printf.c,RTT_Syscalls_KEIL.c) to my bootloader project(Picture 1).
Second,I add...
hai
in nrf51822 the pins p0.01 t0 p0.06 are marked as analog pins in the nrf51822 DK.
i know that in arduino we can use an analog pin as an analog input as well as a digital...
Hello!
I am developing with mbed. According to nRFgo Studio, the hex file generated by the mbed compiler already contains the following SoftDevice: S132_nRF52_2.0.0 (Id...
Hi all, I'm working on sdk11.0.0 and s130 softdevice. In my project I want to send data coming from uart to ble and data coming from ble to uart same as ble_app_uart example...
Hi there,
I am working on programming the CTS ble service on my code.
In order to do that I also have to include db discovery.
#include "ble_cts_c.h"
#include "ble_db_discovery...
Hi,When I use nRF Connect app(IOS version) to connect my ble device,BLE_GATTS_EVT_SYS_ATTR_MISSING log information appears in my RTT Viewer(Picture IOS_Phone_Conncet).After...
Hello,
I tried as you mentioned using sdk12.1.0 buttonless_dfu and bootloader_secure example.
I didn’t modify anything except dfu_public_key.c.
As shown in the attached...
Hello,
I have a program that do an infinite loop in sd_softdevice_enable. How can i investigate ?
Loop is from 0x00009DEA to 0x00009DF2
Target is nRF52832 AA with...
Hi,
I am working on nRF52 with freertos + SDK13.0 + sd S132_4.0.2. I found the device will be trap in the xTaskIncrementTick of the xPortSysTickHandler when some task is...
Hi Nordic, can you please confirm the device ID for nRF51822 QFAA G1?
The HWID I discovered is 0x004A
Pls confirm so I can pull an update request for Black Magic Probe...
