Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hello, I get the
"ERROR: The --family option given with the command (or the default from nrfjprog. ini)
ERROR: does not match the device connected."
message after...
Good morning,
this is Algocraft (www.algocraft.com), an high tech company whose core business is to develop, design and market a wide range of professional systems dedicated...
Hi,
We designed the circuit followed the reference circuit(QFN48), but we always failed in the 8kv ESD test.The CPU always reset while ESD testing.
The 8kv ESD power...
I've completed the Custom service tutorial, and I wanted to port the system to use the SDK10 with the pack installer. I've run into an issue though.
The code runs fine...
Are the GPIO pins in disconnected state during the startup until they are configured by the Firmware?
If not what is the state of the GPIO pins during startup?
Hello.
I have problems uploading with DFU OTA any application. For this case, I am using "dual_bank_ble_s310" example.
First of all, I put this memory's configuration...
Hi,
I am using nrf51822 CDAB version chip which has 128kb of flash memory, my code is built on ble_hrs
I am trying to save my app_trace logs i.e., redirecting my printf...
Hi,
I'm using pca10040 board. For my requirement i'm using FreeRTOS. While creating task we need to set stack size for each task.
For that i created only one task with...
Hello,
i would like to scan for a custom UUID Ventor. And when the BLE Central found this BLE Client.
I will Change one Output pin from low to high.
I start with the...
hi,
after connecting to peripheral device. app_timer_cnt_get() function always gives 0. why it is so. i am not able to understand it.
can anyone help me to get the current...
Hi all,
Can I do something like this:
The SPI master sets CSN line low.
The SPI master sends multiple packets. And the total number of bytes exceeds the...
I want to transfer data collected in my nrf52DK to nRF51 dongle at regular intervals. Right now I can use master control panel in PC to receive the data. Is there any way...
I am using the bootloader from github here to upload DFU over-the-air using an android phone. It works fine for bootloader and application uploads. But if I upload the softdevice...
I'm looking for a radio module for a harsh environment (steelworks furnace)
The module has to work at high temperature 80°C and must transmit 16bytes every second at a distance...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi. I'm using PCA10028, SDK10.0.0, S130.
Recently I'm testing SYSTEMOFF mode.
Unfortunatly My board is not operate now.
KEIL can't connect PCA10028 baord any more.
Here...
i use a ppi channel 0 to connect timer2 and adc,when timer2 compare event happen,the adc task start begin.then,in the adc interrupt handler,i read the adc result into the...
It seems that many people use GCC toolchain (with "high" setup effort) for utilizing SDK in C++ development.
It should however be possible also on Keil with less setup effort...
