I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi!
I am confused regarding NUS, L2CAP, ATT and GATT.
We are using NUS with data length extension to communicate between two nRF52840 boards and want to maximize packet...
Hi, here in the documentation ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/config_and_build/board_support/processing_environments.html ) for the latest...
I have been trying to interface the Witmotion WT901 sensor with the nRF5340 using the I2C interface. I have previously run the exact code on the nRF52DK and it was working...
Due to the allocation of Flash resources, only 100KB ROM for the app , and if we use Keil, we will have about 20KB of margin for additional code development, but we have to...
I'm new to Zephyr and have inherited a project that uses the stm32 h747 disco board. The last build shows:
Memory region Used Size Region Size %age Used
FLASH: 363268...
I'm trying to download a largish file (~167KB) via HTTP/TCP/IPv6 but the modem crashes every time around the same point during the download. It's spits out error 122, which...
Hi,
I just ran into a strange issue and traced it back to a KCONFIG problem... It seems that if I have BOOTLOADER_MCUBOOT and SECURE_BOOT configured "y" I end up getting...
Hello,
I' have problem with CMAKE and Zephyr in VSC. Please, see following error:
[main] Building folder: blinky_13
[main] Configuring project: blinky_13
[proc...
hi,all
I Need add many characteristic with notify in one service,and I wish it can send notify to the phone once the phone enable cccd.
1.tx_handles can work,buf rx_handles...
Good day,
I am developing app by SDK 17.1.0, including ble_nus and ble_hid, I would like to imply fuction to switch between ble_nus and ble_hid, due to some difference configuration...
Hi!
I am trying to subscribe to the power management events that correspond to the following log lines (which I can clearly see in the log):
I have been trying with this...
Hello All,
I'm currently now on the initial phase of development and i wanna to stream 2xIMU data through SPI as for now if i connect only one IMU as Follow
P1.15 SCL...
Dear all and Nordic Staff:
I am learning about dynamic multiprotocols and found examples of dynamic multiprotocols for Thread and BLE in the "nRF5 SDK for Thread and Zigbee...
Due to the system design of our products, I am going to need to sideload any firmware update binaries. That is, my application code will handle receiving the update through...
