Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi guys!
First of all, sorry to make this question here because it is almost unrelated to Nordic, but I am desperate. I developed a device using your nRF52832. I programmed...
Hi,
I have a problem with Thread network stabilty and formation in new SDK for Thread and Zigbee 1.0. Examples seems to work fine in unchanged form, network is stable and...
Repetition of the steps followed here.
(1) Generated priv key, and public_key.c file using nrfutil, (2) generated the bootloader_settings file using nrfutil (3) Compiled...
hi!
nordic team
i am using thingy 52,and i meet a question that app_thingy_s132.axf: Error: L6405E: No .ANY selector matches accel_auto_cal.o(.bss) when i compile this...
Hello,
I am using nrf51822 with sdk11.0.0.
i observe that in while loop sd_app_evt_wait() function take much time for next interrupt to be pick.
is there any alternate...
I am developing a BLE anti-lost APP with community search, I set scan continuously or scan window 5 secs and scan interval 10 secs, but it drain phone's battery. How long...
Hi there,
I am working on having serial bootloader in nrf51422 to perform dfu over UART. DFU serial bootlaoder example in sdk11 claims to do the same.
After flashing...
I can't figure out why I can't send ADC values to the NUS service via BLE correctly. I should be getting hex values that convert to something like 0 or -1, since the ADC pin...
Hi all,
I'm currently learning on how to build bluetooth connections with a device from an app. For that I downloaded the iOS version of the nerf Toolbox app, as my chip...
hi
I am using nRF52 DK
Loaded Blinky Peripheral
I Connected this nRF DK to Com Port and Started Master Control Panel
But the Start Discovery Button is Disable. Please...
Hi,
I have an issue wherein once OTA update is complete through nRFToolbox (Toolbox says " Upload Complete") the Device does not reset and shows that it is connected to...
I am in the development stages of developing a ble application with the nrf52840 nordic chip.
I have come to realize the increasing difficulty of debugging this chip only...
Hello,
I made a custom board based on nRf52832, and I am using SDK 14.2
When I use a slightly modified version of the ble_app_uart example, I see it with nRf Toolbox,...
Hello,
I'm trying to configure 2 serial ports for a custom board with nRF52840 chip, but when I try to instance the second UART "NRF_SERIAL_UART_DEF(serial_uart1, 1);" the...
