I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
in sample peripheral_uart in NCS1.5.0 ,I want to re-binding uart0 rx and tx pin . the default pin is p0.20 and p0.22 ,i want to rebind witn p1.0 and p1.1 .but i edit in prj...
Hello, I bought the Bluefruit LE Sniffer - Bluetooth Low Energy (BLE 4.0) - nRF51822 - V3.0 from Adafruit Bluefruit.
So, I downloaded nRF Sniffer for Bluetooth LE 3.0 and...
Hi,
I am trying to apply a whitelist during advertisement on my peripheral device. Only one central should be whitelisted at a time. The whitelist is empty on initial...
Hi,
I'm using nRF52840 with ble_app_uart of ble peripheral example. And I'm using IDE is SES.
I want to put two deep learning model into my project , the two deep learning...
Hello,
I have the NCS v1.5.0 and would like to use AES (in different modes) in my non-secure application.
Looking at the crypto libraries available described here http...
Hi,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK. One board is programmed with the proxy client , and the other with the proxy server...
Hello I am in the process of developing a central BLE and I would like to be able to transmit 240 byte frames with a device. The problem I have during my tests is that I see...
Hi,
I get " Could not fetch memory size of target devkit: Error: Error occured when get library info. Errorcode: CouldNotOpenDevice (0x4) Lowlevel error: LOW_VOLTAGE (fffffff4...
I want to use 9 axis motion sensor and I am planning to use INVENSENSE ICM-20948 for this. I know that all the sensors can interface with I2C protocol but the problem is I...
Hello,
DK: nrf52840
SDK: 15.0.0
i want to advertise accelerometer data with BLE/Beacon
so i tried to update the adv. packet for every 10 sec but its not advertising...
BLE DFU Mcu Mgr Error: NOT_SUPPORTED (8)
I am testing the DFU via BLE and get the message "NOT_SUPPORTED (8)" Does anyone have an idea what is not supported?
I logged the following error when I connect my PCA10040 nRF52 development board. The error is: Could not fetch memory size of target devkit: Error: Error occured when get...
Hi there,
First of all; I have experience in Keil but I am new to SEGGER and Zephyr.
Rebuilding our project in Segger using the new nRF Connect SDK I am stuck at adding...
Hi,
I'm running example mqttsn_sleepy_subscriber from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 on a nRF52840-DK with Paho MQTT-SN gateway on a Raspberry Pi 3 running...
