Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I want to let nRF9160DK communicate with an external module through UART in nRF9160DK
Then I need to assign rx and tx on two pins.
I will use UART0 for printk function...
Hey all!
I have a problem with my custom board using the nRF52832 with Softdevice 6.0 and SKD 15.0.0 working on Windows 10 in SEGGER with the BMD-300. I have the following...
We're using an nRF52832, SDK14.0.0, SoftDevice 132 v5.
Early in our firmware lifecycle, before SoftDevice is enabled, we configure our PMIC. This involves performing some...
I used SDK is nRF5_SDK_14.1.0_1dda907
Chip is nrf52832 evb.
Soft device is S332.
I call function sd_power_system_off() enter system off.
Use triggered from DETECT...
Hi..
I have try to lookup in devzone q&a, but seems not yet found the similar question or answer. Have try SR3 SDK and able to implement keyboard+consumer control for remote...
Hi Sir,
As runs w/ serial DFU and check the source code of nrfutil, it support to send the rest of page when transmitted the data.
1. If we don't want to implement this...
I want to advertise coded phy and 1M. This isn't possible at the same time so I am using the ble_gap_adv_params_t duration to timeout my 1M advertising every 600 ms to switch...
Hello,
I am building an application where client sends a fixed number of packets (10Bytes/packet) to a server with different values of advertisement interval. I changed...
Hi,
I'm developing a smartwatch that relies on low latency communication with local web servers. I'm in the very begining but I'm sure that the latency added between the...
Hello, I need to use MQTT over NB IoT with nRF9160. Task to connect to Amazon AWS over NB IoT with MQTT. As I understand correctly, NB IoT doesn't support TCP, so I can't...
Hi,
I was trying to download nrf5_sdk_for_mesh_v3.1.0_src.zip, which is at : https://www.nordicsemi.com/Software-and-Tools/Software/nRF5-SDK-for-Mesh/Download#infotabs,...
Hi all, I am working on a project for which I use nRF52832 with SDK15.2 and SD132. What I need is that nRF52 should transmit and receive command through serial UART as a central...
Hi, I am trying to setup a mesh architecture, and I am not sure which path to take (Thread / Zigbee / Etc). The architecture is for the following system.
There will be...
hello, i am trying an example of a Node running multi-peripheral with ble_nus service. I have a question: Suppose when Node receives a packet from central A, Node will call...
